Work Pro W ControlOne Manual Del Usuario

ControlOne
ControlOne is a great solution for architectural lighting control with 1 channel dimmers This wall-mount remote control allows an intuitive
control of lighting intensity in an installation.
Its encoder works sending a DMX signal, (1 channel), the level of this channel will mark the level of intensity.
A frame around the encoder shows the intensity level sent to the dimmer.
The DMX starting address can be setup through dip-switch block.
The unit incorporates power failure memory function.
OPERATION
1. Connect the main supply and DMX signal to the ControlOne
according the diagram. Be sure the polarity of both connections
(supply and DMX signal).
2. Using the dip-switch block, setup the correct DMX starting address.
NOTE: For a better
ON
1=
understanding. the
square in white color
is considered the switch
9
in all pictures of this
0=OFF
user manual
DMX is an universal binary language used as a form of communication between intelligent fixtures. Each Dip Switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
3. Rotate the encoder on the control panel in clockwise, the DMX sending out will increase up to maximum level (255). Turning in anti-clockwise,
the value will decrease up to minimum value (0). On both modes, the illuminated frame will indicate the intensity level.
4. Press the encoder once, The DMX value will turn to be opposite to the present value. For example, if the present value is 10, it will turn to
245 (255-10=245) within certain fadetime. However, it will keep on the present value if you rotate the encoder. Pressing the encoder again, the
function will be disable and the intensity value will be changed turning the encoder again.
5. Dip swtich number 10 is used to ser fade time. It will be fast (from 0 to 255 in about 3 seconds) if dip is flipped to "ON", and it will be slow
(about 6 seconds) if the dip is flipped to "OFF".
TECHNICAL DATA
Main Supply:
Connection:
Operating Temperature:
Dimensions:
This symbol on the product or on its packaging indicates that this product
shall not be trated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical an electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of amterials will help to conserve natural
resources. For more detailed information sabout recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
User Manual
DMX starting address
1 2 3 4 5 6 7 8 9 10
For example: Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON"position
Dipswitches#
DC 9 V
Terminals
Housing: Polycarbonate
Control: 1 DMX channel
-10º to +50ºC
86 x 86 x 45 mm
Weight: 200 g
1= ON
4 3 2
0=OFF
START
1=1
CH#
3=4
5=16 Value
1
=21
2
3
4
5
6
7
8
9
10
+
ControlOne PCB
Rear Side connections
and controls
1. GND
2. DMX SIGNAL -
3. DMX SIGNAL +
4. + 9 V DC
1
1= ON
1 2 3 4 5 6 7 8 9 10 11 12
0= OFF
START
SWITCHES ON
CH#
1 11
2 12
1,2
13
3 14
1,3
15
2,3
1,2,3
4
1,4
2,4
ControlOne
TOGGLE
EN
SWITCHES ON
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1,2,3,4,5,6,7,8,9
Bright
V 1.0