American Standard COLONY SOFT 1655SS.502 Instrucciones De Instalación

COLONY SOFT
PRESSURE BALANCING BATH AND SHOWER SETS
JUEGOS DE BAÑERA Y DUCHA CON PRESIÓN EQUILIBRADA
ENSEMBLES DE BAIN ET DOUCHE À ÉQUILIBRAGE DE PRESSION
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad
durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure
depuis plus de 100 ans. Pour vous assurer que l'installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
ROUGHING-IN DIMENSIONS
To assure proper positioning in relation to wall, note roughing-in dimensions.
Tome nota de las dimensiones de desbastado para asegurar la posición correcta respecto de la pared.
Pour garantir un bon positionnement par rapport au mur, tenir compte des dimensions de préparation.
FINISHED WALL
PARED TERMINADA
MUR FINI
4" REF.
4" (102 MM) REF.
RÉF. 102 mm (4 po.)
5-1/2" REF.
5-1/2" (140 MM) REF.
RÉF. 140 mm (5-1/2 po.)
"SEE ILLUSTRATION "
VEA LA FIGURA INFERIOR
VOIR INSTALLATION CI-DESSOUS
74" FOR HEAD CLEARANCE
74" (188 CM) DE ALTURA
188 cm (74 po.) POUR DÉGAGER LA TÊTE
18" OPTIONAL
18" (45,7 CM) OPTATIVO
OPTION 45,7 cm (18 po.)
1" MIN.
1" (25 MM) MÍNIMO
MIN. 25 mm (1 po.)
*5-1/8" REF.
5-1/8" (130 MM) REF.
RÉF. 130 mm (5-1/8 po.)
TOP OF TUB RIM
BORDE SUPERIOR DE LA BAÑERA
HAUT DE REBORD DE BAIGNOIRE
BOTTOM OF TUB
FONDO DE LA BAÑERA
FOND DE BAIGNOIRE
1
ROUGHING-IN
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When
NOTE finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard
to continue installation. Use thread sealant or Teflon tape on threaded connections.
See Roughing-in diagram before starting.
Connect RISER PIPE (1) to MANIFOLD (2)
top outlet marked "SHR".
Connect TUB FILLER PIPE (3) at bottom
outlet marked "TUB".
Supply connections are:
1/2" copper sweat for sweat inlets
1/2" female NPT for threaded inlets
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD (4).
1655SS.502
1655.502
1675.502
1675SS.502
DIMENSIONES DE DESBASTADO
1-5/8" TO 3-1/4"
1-5/8" A 3-1/4" (41 MM A 83 MM)
41 mm (1-5/8 po.) À 83 mm (3-1/4 po.)
1/2" NPT
1/2" (12,7 MM) NPT
12,7 mm (1/2 po.) NPT 3-3/8"
3-3/8" (86 MM)
86 mm (3-3/8 po.)
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78'
'
TUB PORT 1/2" NPT
OPTATIVO AL PISO TERMINADO,
ORIFICIO DE BAÑERA,
POR LO GENERAL ENTRE
1/2" (12,7 MM) NPT
65" Y 78" (165 A 198 CM)
'
ORIFICE BAIGNOIRE NPT
HABITUELLEMENT ENTRE
12,7 mm (1/2 po.)
165 cm (65 po.)
ET 198 cm (78 po.)
ENTRE OPTION ET PLANCHER FINI
SHR. 1/2" NPT
DUCHA, 1/2" (12,7 MM) NPT
DOUCHE NPT 12,7 mm (1/2 po.)
6"
6" (152 MM)
152 mm (6po.)
TUB PORT 1/2" NPT
ORIFICIO DE BAÑERA,
1/2" (12,7 MM) NPT
ORIFICE BAIGNOIRE NPT
12,7 mm (1/2 po.)
*FOR COPPER SWEAT
OR SLIP-ON ONLY
1/2" COPPER
4"
OR1/2" NPT'
'
4" (102 MM)
1/2" (12,7 MM) COBRE
102 mm (4 po.)
O 1/2" (12,7 MM) NPT'
'
CUIVRE 12,7 mm (1/2 po.)
OU NPT 12,7 mm (1/2 po.)
CAUTION Turn off water at main supply.
If the valve is installed on a fiberglass
or other thin wall application, the
PLASTER GUARD (4) can be used as a support.
Cut a 3" dia. hole in the shower stall.
If STOPS are used, drill two additional
1" holes to allow access to the stops.
Remove PLASTER GUARD (4), rotate 90 degrees
so that indicated screw holes fit MANIFOLD (2).
Push CAP on valve, place ESCUTCHEON on and
attach with screws.
Connect hot and cold water supplies.
Cap off shower pipe (5) and tub filler pipe (6).
For support, use pipe BRACES (7) secured to wooden
braces.
With valve turned off, turn on water supplies.
Check for leaks.
Installation Instructions
Instrucciones de instalación
Mode d'installation
1655SS.501
1655.501
1675.501
1675SS.501
INLETS 3-3/8"
ENTRADAS, 3-3/8" (86 MM)
ENTRÉES 86 mm (3-3/8 po.)
SHR. 1/2" NPT
DUCHA, 1/2" (12,7 MM) NPT
DOUCHE NPT 12,7 mm (1/2 po.)
INLETS 1/2" NPT
ENTRADAS, 1/2" (12,7 MM) NPT
ENTRÉES NPT 12,7 mm (1/2 po.)
THREADED INLETS
'
ENTRADAS ROSCADAS
' ENTRÉES FILETÉES
5-7/8"
5-7/8" (149 MM)
149 mm (5-7/8 po.)
3-3/8"
3-3/8" (86 MM)
86 mm (3-3/8 po.)
'
THREADED INLETS (STOPS)
'
ENTRADAS ROSCADAS (LIMITADORES)
ENTRÉES FILETÉES (BUTÉES)
INLETS 1/2" NOM. COPPER SWEAT
ENTRÉES CUIVRE LISSE 12,7 mm
BAÑERA, 1/2" (12,7 MM) NOM. COBRE SOLDADO
CUIVRE LISSE 12,7 mm (1/2 po.) NOM. BAIGNOIRE
1655SS.500
1655.500
1675.500
1675SS.500
Certified to comply with ANSI A112.18.1
Cumplimiento certificado de los requisitos
de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750
DIMENSIONS DE PRÉPARATION
INLETS
4-1/16"
ENTRADAS,
4-1/16" (103 MM)
ENTRÉES 103 mm
(4-1/16 po.)
SHR. 1/2" NOM.
COPPER SWEAT
'
DUCHA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
'
CUIVRE LISSE 12,7 mm
(1/2 po.)NOM. DOUCHE
TUB 1/2" NOM.
COPPER SWEAT
'
BAÑERA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
'
CUIVRE LISSE 12,7 mm (1/2 po.)
NOM. BAIGNOIRE
ENTRADAS SOLDADAS
INLETS 1/2" NPT
ENTRADAS, 1/2" (12,7 MM) NPT
ENTRÉES NPT 12,7 mm (1/2 po.)
SHR. 1/2" NOM. COPPER SWEAT
DUCHA, 1/2" (12,7 MM) NOM. COBRE SOLDADO'
CUIVRE LISSE 12,7 mm (1/2 po.) NOM. DOUCHE
5-7/8" (149 MM)
149 mm (5-7/8 po.)
'
ENTRADAS, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
(1/2 po.) NOM.
TUB 1/2" NOM. COPPER SWEAT
SWEAT INLETS (STOPS)
ENTRADAS SOLDADAS (LIMITADORES)
ENTRÉES LISSES (BUTÉES)
1
2
HOT
CALIENTE
CHAUD
M 9 6 8 7 4 1
INLETS 1/2" NOM.
COPPER SWEAT
'
ENTRADAS, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ENTRÉES CUIVRE LISSE 12,7 mm
(1/2 po.) NOM.
2"
2" (51 MM)
51 mm (2 po.)
4-1/16"
4-1/16" (103 MM)
103 mm (4-1/16 po.)
SWEAT INLETS
ENTRÉES LISSES
5-7/8"
4-1/16"
4-1/16" (103 MM)
103 mm (4-1/16 po.)
5
7
COLD
FRÍA
4
FROID
PLUG
TAPÓN
BOUCHON
3
6