Publicidad
Idiomas disponibles
Idiomas disponibles
2
B (adattatore BPT per placca
VIMAR)
C (telaio BPT)
D (adattatore copriforo BPT)
E (placca VIMAR serie Idea o
Rondò).
3 (fig. 8)
A (scatola incasso)
B (telaio BPT)
C (adattatore copriforo BPT senza
aste di unione)
D (placca GEWISS serie Playbus).
Esempi di montaggio del modulo
monitor NVM/200 in una scatola
incasso unificata da sei moduli
abbinato al modulo viva-voce
NC/221 con alcune placche in com-
mercio:
4 (fig. 9)
A (scatola incasso)
B (telaio BPT) (kit NS/6)
C (adattatori copriforo BPT da 11
mm) (kit NS/6)
3
D (placca BTICINO serie Living art.
L4807 o Light art. N4807).
5 (fig. 9)
A (scatola incasso)
B (telaio BPT) (kit NS/6)
C (adattatori copriforo BPT da 9
mm) (kit NS/6)
D (placca VIMAR serie Idea o
Rondò, placca GEWISS serie
Playbus,
placca
Sistema 45).
ATTENZIONE. Quando vengono
utilizzate placche BTICINO (serie
Living o Light) e placche GEWISS
(serie Playbus) devono essere eli-
minati gli agganci indicati in fig. 10;
mentre utilizzando placche VIMAR
(serie Idea o Rondò) devono esse-
re eliminati gli agganci indicati in
fig. 11.
4
INSTALLATION
GB
INSTRUCTIONS
NVM/200 COLOUR
MONITOR MODULE
Colour monitor to be used in
conjunction with the hands-free
module NC/221 in series 200 video
entry control installations.
It can be inserted on its own in a
standardised rectangular single
embedding box, or combined with
the hands-free module in a stan-
dardised double embedding box.
The unit comes with a chassis and
adapters for the use of a number of
commercially available front plate
models.
It features the following controls
(fig. 1):
Brightness
5
Entry panel activation
•
Centralized
light, selection of entry panel)
Colour saturation.
To adjust colour saturation,
activate the system using the
entry panel activation push-
boton and keep it pushed
down
while you press the
brightness + and – buttons.
This operation cannot be
performed if the entry panel
activation
released before the appro-
priate
made, or if the monitor has
been activated by a call from
the entry panel.
Function of each terminal (fig. 2)
3
video signal
4
video signal shield cable
If the line does not continue, con-
nect the 75Ω resistance (violet-
green-black-gold) between termi-
nals 3 and 4 and 4.
3
positive v. signal
4
negative v. signal
If the line does not continue, con-
nect the two 56Ω resistances
(green-blue-black-gold) between
terminals 3-5 and 4-5.
5
– 14÷17.5 V
6
+ monitor power supply
7
input call from entry panel
8
audio from entry panel
AVE
serie
9
audio to entry panel
E
enabling receiver
Technical features
• Video signal system: PAL.
• Display: 2" colour LCD Poly-
Silicon TFT.
• Resolution: 521x218 dots.
• Supply voltage: 14÷17.5 V DC.
• Current demand: max. 220 mA
(5 mA in standby).
• Video input: 1 Vpp (in the range
0.7 to 1.5 Vpp) from coaxial line;
V+ 0.6, Vpp V– 0,6 Vpp (in the
range 0.3 to 0.9 Vpp) from diffe-
rential line (twisted pair).
• Video input impedance: 5 kΩ.
• Working temperature range:
from 0 °C to +35 °C.
Installation
The monitor module can be instal-
led on its own in conjunction with
the hands-free module NC/221
(fig. 3), or combined with the
hands-free module in a single
embedding box (fig. 4).
Recess the embedding box flush
with the wall at a suitable height for
the user.
WARNING. To remove the monitor
module from the chassis, lift the
locking clips and push from the
rear (fig. 5).
Examples of assembly of the
NVM/200 monitor module in a stan-
dardised single embedding box
with a number of commercially
available front plates:
1 (fig. 6)
A (embedding box)
B (BPT chassis)
control
(stair
pushbutton
is
adjustements
are
coaxial
twisted
pair
Publicidad
