Parts2o FPP1520 Manual Del Usuario

Paquete de revisión para bombas de chorro de pozos poco profundos, resistentes a la corrosión

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Phone: 1-877-PUMP-P2O (877-786-7726)
Web Site: http://parts2o.com
PUMP DISASSEMBLY
(See Figures 1 and 2)
1.
Hazardous voltage.
Disconnect power to motor (see
Figure 1) before servicing pump.
2. Open faucets or lines to release all
pressure in system before proceeding.
Figure 1
3. Disconnect wires to pressure
switch.
4. Remove pressure switch tube from
barbed elbow on pump body and
allow pump to drain.
5. Remove four hex nuts which hold
the pump body to the motor.
6. Remove the motor, seal plate,
impeller, diffuser and pad as a unit
(See Figure 2).
Slide motor away
from pump
Figure 2
CLEANING/REPLACING IMPELLER
NOTE: First, follow instructions under
"Pump Disassembly".
1. Remove two screws fastening dif-
fuser to seal plate; remove diffuser
(See Key Nos. 9 and 10, Figure 15).
Exposed impeller can now be
cleaned.
2. If impeller must be replaced, loosen
two machine screws and remove
motor canopy (See Figure 3). If
motor has a capacitor, go to step 3.
If motor does not have a capacitor,
go to step 6.
Corrosion Resistant Shallow Well
be hazardous. To discharge capacitor,
hold insulated-handle screwdriver by the
handle and short capacitor terminals
together. Do not touch metal screw-
driver blade or capacitor terminals. If in
doubt, consult a qualified electrician.
Figure 3
3. Unscrew capacitor clamp and
remove capacitor. Do not dis-
connect capacitor wires to motor.
4. Slide 7/16" open end wrench in
behind spring loaded switch on
motor end of shaft; hold motor shaft
with wrench on shaft flats and
unscrew impeller by turning counter-
clockwise when looking into eye of
impeller.
5. To reinstall, reverse steps 1 through
4. Mount diffuser as shown in
Figure 11.
6. See directions under "Pump
Reassembly".
CLEANING/REPLACING THE
SHALLOW WELL EJECTOR
NOTE: First, follow instructions under
"Pump Disassembly".
1. Unscrew venturi and remove it (See
Figure 4).
Turn counterclockwise
to remove
Figure 4
For further operating, installation, or maintenance assistance:
1-877-PUMP-P2O
Jet Pump Overhaul Kit
Capacitor voltage may
To avoid
electrical shock
hazard, use
insulated-handle
screwdriver to
short capacitor
terminals.
Venturi
(1-877-786-7726)
FPP1520, FPP1521
2. If necessary, unscrew and remove
nozzle with a 5/8" deepwell socket
wrench (See Figure 5).
Nozzle
5/8" Deep-well socket
Figure 5
3. Clean venturi and nozzle by care-
fully inserting an ice pick or other
small diameter pointed tool, dis-
lodging foreign material.
IMPORTANT: Be careful not to enlarge
hole in nozzle or venturi. If venturi and
nozzle cannot be cleaned or are dam-
aged while cleaning, replace.
4. Reinstall venturi and nozzle by
threading clock-wise into pump
ejector body insert until snug. Do
not overtighten.
5. See directions under "Pump
Reassembly".
REMOVING OLD SEAL
1. Follow instructions under "Pump
Disassembly."
2. Follow steps 1 through 5 under
"Cleaning/Replacing Impeller."
3. Remove rotating half of seal by
placing two screwdrivers under seal
plate and carefully prying up
(Figure 6). Seal plate will slide off
shaft, bringing seal with it.
Figure 6
P2O-29 (9/4/07)
Ejector
body
insert
507 0194
( continued )

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Parts2o FPP1520

  • Página 1 Corrosion Resistant Shallow Well Jet Pump Overhaul Kit Phone: 1-877-PUMP-P2O (877-786-7726) FPP1520, FPP1521 Web Site: http://parts2o.com PUMP DISASSEMBLY 2. If necessary, unscrew and remove Capacitor voltage may (See Figures 1 and 2) nozzle with a 5/8" deepwell socket be hazardous. To discharge capacitor, wrench (See Figure 5).
  • Página 2 REMOVING OLD SEAL (continued) Top of motor flange IMPORTANT: Be sure you do not Be Careful ...Does Not scratch or mar shaft; if shaft is marred, it That Motor Damage Seal Face must be dressed smooth with fine emery Shaft Shoulder... or crocus cloth before installing new seal.
  • Página 3: Pump Reassembly

    Properly Properly seated Seated 039 0893 Figure 12 Figure 14 6. Follow steps 2 through 11 under “Installing New Seal”. Pump Brand For Use With Kit No.: FPP1520 FPP1521 Flotec FP4001-08, FP4012-08 FP4022-08 Simer 3105P 3107P Teel 4AT96, 4AT97 4AT98...
  • Página 4 Port 1867 0795WWG Figure 15 Kit Contents Key No. Part Description Qty. FPP1520 FPP1521 Water slinger 17351-0009 17351-0009 Heat sink J3-2 J3-2 O-ring U9-390 U9-390 Shaft seal U109-6A U109-6A Impeller J105-40P J105-42PTB Rubber pad C35-41 C35-41 Diffuser N1-28P N1-28P Parts Not Included With Kit Key No.
  • Página 5: Démontage De La Pompe

    Trousse de réparation des pompes à éjecteur résistant à la corrosion pour puits peu profonds DÉMONTAGE DE LA POMPE 2. Au besoin, dévisser l’ajutage avec La tension du conden- une clé à douille profonde de 5/8 de (Voir les Figures 1 et 2) sateur peut être dangereuse.
  • Página 6 DÉPOSE DE L’ANCIEN JOINT (suite) S’assurer que Be Careful IMPORTANT : Faire bien attention de bas. Le haut de la plaque ...n’endommage pas ...Does Not That Motor l’épaulement ne pas rayer l’arbre; si l’arbre est rayé, d’étanchéité est repéré « TOP » Damage Seal Face la surface du joint Shaft Shoulder...
  • Página 7: Remontage De La Pompe

    039 0893 Figure 14 6. Suivre les opérations 2. à 11. figu- Figure 12 rant sous « Pose d’un joint neuf ». Marques de pompes À utiliser avec les trousses numéro FPP1520 FPP1521 Flotec FP4001-08, FP4012-08 FP4022-08 Simer 3105P 3107P...
  • Página 8: Contenu De La Trousse

    Orifice du régulateur de Port volume d’air 1867 0795WWG Figure 15 Contenu de la trousse Réf. Désignation des pièces Qté FPP1520 FPP1521 Déflecteur d’eau 17351-0009 17351-0009 Dissipateur de chaleur J3-2 J3-2 Joint torique U9-390 U9-390 Joint de l’arbre U109-6A U109-6A...
  • Página 9: Desensamblaje De La Bomba

    Paquete de revisión para bombas de chorro de pozos poco profundos, resistentes a la corrosión DESENSAMBLAJE DE LA BOMBA 2. De ser necesario, destornille y La tensión del capaci- saque la boquilla con una llave de (Consulte las Figuras 1 y 2) tor puede ser peligrosa.
  • Página 10: Instalación De La Nueva Junta

    REMOCIÓN DE LA JUNTA USADA (continuación) IMPORTANTE: Asegúrese de no rayar abajo; la placa de estanqueidad Asegúrese de que Be Careful está marcada en la parte superior ...no dañe la cara ni estropear el eje; si el eje se estropea, ...Does Not That Motor el hombro del eje...
  • Página 11: Instalación Del Difusor Térmico De Cobre

    039 0893 Figura 14 6. Siga los pasos 2 al 11 en la sección “Instalación de la nueva junta”. Figura 12 Marca de la bomba Para usar con el Paquete No.: FPP1520 FPP1521 Flotec FP4001-08, FP4012-08 FP4022-08 Simer 3105P 3107P...
  • Página 12: Contenido Del Paquete

    Toma del regulador de Port volumen de aire 1867 0795WWG Figura 15 Contenido del paquete Clave No. Descripción de la pieza Cantidad FPP1520 FPP1521 Deflector de agua 17351-0009 17351-0009 Disipador térmico J3-2 J3-2 Aro tórico U9-390 U9-390 Junta del eje...

Este manual también es adecuado para:

Fpp1521

Tabla de contenido