Budda BULLY Manual De Instrucciones página 37

BULLY™ GUITAR AMPLIFIER
(84) Reverb / Preset #4
NORMAL mode: This turns the REVERB on and off. The LED will be lit GREEN.
PRESET mode: This selects Preset 4. If selected, the LED will be red.
(85) Over Boost / Preset #5
NORMAL mode: This turns OVER BOOST on and off for the current channel. When switching between channels, this will
remember what the last setting was for each. The LED will be green when OVER BOOST is on.
PRESET mode: This selects Preset 5. If selected, the LED will be red.
(86) Channel Select 1 / Preset #6
NORMAL mode: This selects Channel 1. The LED will be lit GREEN. If pressed a 2nd time, the channel will return to the previous
setting. This allows quick changing between two channels using a single switch.
PRESET mode: This selects Preset 6. If selected, the LED will be red.
(87) Channel Select 2 / Preset #7
NORMAL mode: This selects Channel 2. The LED will be lit GREEN. If pressed a 2nd time, the channel will return to the previous
setting. This allows quick changing between two channels using a single switch.
PRESET mode: This selects Preset 7. If selected, the LED will be red.
(88) Channel Select 3 / Preset #8
NORMAL mode: This selects Channel 3. The LED will be lit GREEN. If pressed a 2nd time, the channel will return to the previous
setting. This allows quick changing between two channels using a single switch.
PRESET mode: This selects Preset 8. If selected, the LED will be red.
(89) Master Boost / Preset #9
NORMAL mode: This turns the Master Boost on and off. The LED will be lit green.
PRESET mode: This selects Preset 9. If selected, the LED will be red.
Using Preset Mode
Each of the 9 presets remembers the current channel, over-boost on/off, reverb on/off, effects loop on/off and master boost
on/off. Additionally, it remembers the over-boost and effects loop status of the two inactive channels. This way you can, for
example, have a clean preset saved without over-boost, and know that when you switch to Channel 2, over-boost will be on.
The amp comes from the factory with 9 default presets that you can modify at will. When the PRESET MODE light is on, you can
use the 9 other footswitches to recall those 9 presets. At any time you can switch to NORMAL mode and make changes to that
sound. This can be during a performance and not permanently stored, or to edit a preset and store to one of the 9 settings.
Storing Presets
To store the current settings into one of the 9 presets, you start by holding the PRESET MODE switch down for a second or two,
after which the other LEDs will blink (except the one for the current preset which will be on steady – a way to remind you of
which preset you were working with). At this point you can press one of the 9 preset switches to store there, or press PRESET
MODE again to cancel.
You can initiate this from PRESET mode or from NORMAL mode. After the store (or cancel) it will return to the mode you were
in. So you can setup and store 9 presets without ever entering PRESET mode if you wish. It's typical to set up your sound in
NORMAL mode, then store your creation to one of the presets.
Linking to another amp and/or effects units with the MIDI Out
You can connect the MIDI Out to the MIDI In of another BULLY to synchronize the two amps. With the footswitch connected to
the first amp, any changes you make with the footswitch (or front panel) will be duplicated on the 2nd amp – if the 2nd amp is on
the same MIDI channel.
You can also link the MIDI from the amp (or from the 2nd amp) to an effects unit to synchronize presets. If the effects unit can
store presets, they can change automatically when you recall presets on the footswitch.