Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para Timberkits Bi-Plane
Resumen de contenidos para Timberkits Bi-Plane
- Página 1 Timberkits Bi-Plane...
- Página 2 (IT) Leggere tutte le istruzioni e guardare i diagrammi instructional videos where you (DE) Lesen sie alle anweisungen und betrachten sie die schaubilder see this symbol. www.timberkits.com (UK) Check assembly before gluing (FR) Vérifier le montage avant collage (ESP) Controlar el montaje antes de empezar a pegar (IT) Controllare l’assemblaggio prima di incollare...
- Página 3 Or visit our website for tips, advice and instructional videos. All these can be found in Resources/Advice Videos on our website.
- Página 5 10 (x6)
- Página 6 2mmx6mm 3mmx12mm x9 6mmx25mm 2mmx8mm 2mmx10mm 3mmx25mm 5mmx35mm 2mmx14mm 3mmx28mm 2mmx20mm 2mmx22mm 3mmx33mm 5mmx38mm 2mmx50mm 6mmx49mm 3mmx56mm 6mmx56mm 3mmx62mm 5mmx62mm 5mmx95mm 47 x2 42 x4 41 x2...
- Página 7 15mins 5mmx35mm...
- Página 8 3mmx12mm 3mmx12mm Roughen up the surface of the 6mm x 49mm shaft and then apply a generous amount of glue to the area on the shaft that is being glued in part 11. This glue joint must be very strong. 6mmx49mm 10mm...
- Página 9 3mmx56mm 3mmx56mm 5mmx35mm 5mmx35mm...
- Página 10 3mmx12mm 3mmx12mm...
- Página 11 5mmx62mm 5mmx38mm 10mins...
- Página 12 3mmx12mm 15mins...
- Página 13 6mmx56mm 6mmx25mm...
- Página 15 3mmx25mm 3mmx56mm 15mins...
- Página 16 3mmx25mm 3mmx12mm...
- Página 17 12mm 5x95mm 15mm 10mins 3mmx12mm 3mmx28mm...
- Página 18 2mmx50mm...
- Página 19 2mmx10mm 2mmx10mm 5mmx62mm 10mins Bevel outer edge of part 30 with sandpaper and wax, then glue behind part 28.
- Página 20 Bevel edge with sandpaper provided 20mins...
- Página 21 2mmx22mm 2mmx20mm...
- Página 22 2mmx6mm...
- Página 23 3mmx12mm 20mins 20mins...
- Página 24 20mins...
- Página 25 3mmx33mm 3mmx33mm 3mmx62mm 2mmx14mm...
- Página 26 20mins...
- Página 27 2mmx8mm 2mmx8mm The blocks part #9 are aysemetric. Ensure correct alignment as shown in diagram. The blocks part #10 are asymmetric. Ensure correct alignment as shown in diagram.
- Página 28 The blocks part #10 are asymmetric. Ensure correct alignment as shown in diagram. Ensure all the wing struts (part #42) are angled towards the front of the 20mins plane when assymbling. rear of plane front of plane...
- Página 29 20mins Use plenty of glue on the edge of the lower wing and the block #9. Ensure its fully dry before fitting other wing. Use plenty of glue on the edge of the lower wing and the block #9. 20mins 20mins...
- Página 30 Hook band around pully wheel...
- Página 31 Alter tilt of plane using the 2 holes in top of link (44) then glue 3x12mm peg in place...
- Página 34 Notes...
- Página 35 (UK) If you enjoyed building this model why not try our others. Available directly from Timberkits Ltd or from our UK, European or worldwide retail partners. Check our website to find your nearest stockist. (FR) Si vous avez apprecie construire ce modele, pourquoi ne pas en essayer d’autres. Ils sont disponibles chez Timberkits Ltd ou chez nos partenaires detaillants au Royaume Uni, en Europe et plus largement dans le monde.
- Página 36 Timberkits Limited Old Village Hall Llanbrynmair Powys, SY19 7AA 00 (44) (0) 1650 521635 timber_kits@btconnect.com www.timberkits.com Timberkits logo and all Timberkits designs are Copyright (©) 2012 all rights reserved.