For Your Safety; Tool Specifications; Operating Controls; Intended Use - Wurth Master ISS 45-M automatic Instrucciones Para El Manejo

ISS 45 - GB Seite 11 Dienstag, 13. Februar 2007 2:43 14
GB
Working safely with this machine is
possible only when the operating
and safety information are read
completely and the instructions con-
tained therein are strictly followed.
In addition, the general safety in-
structions in the enclosed booklet
must be followed.
If the mains cable is damaged or cut
through while working, do not touch
the cable but immediately pull the
mains plug. Never use the machine
with a damaged cable.
For dry vacuuming, a dust bag and a flat-folded
filter element must always be used. Do not operate
the vacuum cleaner without the filter system, other-
wise the vacuum motor will be damaged and a
health risk will be presented due to an increased
amount of expelled fine dust.
An adequate ventilation rate L is required when
the exhaust air is pumped back into the area. In or-
der to keep within the required limit values, the vol-

Tool Specifications

Industrial vacuum cleaner
Article number
Input power
Drum capacity
Gross
Wet
Air flow
Vacuum
Surface of the flat pleated filter
Automatic filter cleaning
Remote automatic starting
- Rated Load of Power tool
- Switch-on delay
- Run-on period
Ambient temperature
Air humidity
Hose diameter
Hose length
Dimensions (L x W x H)
Weight
Safety class

For Your Safety

Use only original Würth parts and accessories
ISS 45-M automatic
701 146 X
1200 W
43 l
30 l
3
150 m /h
10 Electrodes
220 mbar
Not all of the accessories illustrated or described are included
0.6 m 2
as standard delivery.
100 - 2200 W
0.5 s
15 s
The machine is intended for vacuuming dry, non-flam-
mable, harmful dusts from machines and devices of dust
-10 °C – +40 °C
category M according to EN 60 335-2-69. Limitation:
30 % - 90 %
Carcinogenic materials, except for wood dust, may not
35 mm
be vacuumed.
3 m
This appliance is suited for the commercial use, e.g. in
520 x 380 x 695 mm
hotels, schools, hospitals, factories, shops, offices, and
rental companies.
approx. 13.7 kg
The machine is intended for wet and dry vacuuming of
/ I
œ
walls and floors for commercial use.
For damage caused by usage other then intended, the
user is responsible.
ume flow of the air pumped back into the area
must not exceed 50% of the amount of fresh air
(room volume V x ventilation rate L
R
ing applies without special ventilation measure:
L =1h –1 .
W
Usage of the machine and the substances that are to
be vacuumed, including the safe procedure for dis-
posal of the vacuumed material, are to be carried out
only through trained personnel.
This machine contains harmful dust. Emptying
and maintenance work, including the removal of
the dust collection containers, may only be carried
out by skilled personnel wearing suitable protec-
tion. Do not operate the machine without the com-
plete filtration system. The relevant safety regula-
tions that apply for the materials being vacuumed
are to be observed.
In the case of non-conductive fluids (e. g. drilling
emulsions, oils and greases), the unit is not
switched off when the container is full. The fill level
must be regularly checked and the container emp-
tied before it is too full.
Use only original Würth parts and accessories.

Operating Controls

1 On/Off switch
2 Filter dedusting switch
3 Socket for power tool
4 Switch for manual/automatic operation mode
5 Regulator for minimum volume flow
6 Regulator for vacuuming capacity
7 Brush inserts
8 Squeegee inserts
9 Flat pleated filter

Intended Use

). The follow-
W
11