Publicidad
FUNCTION LAYOUT
SETUP
POWERING ON YOUR STIR IT UP WIRELESS
LEGEND
A. RCA Line Out
E. Bluetooth® Button
B. Pre-Amp Switch Button
F. - VOL + Knob
C. USB to PC Recording
G. Headphone Jack
D. Off/33/45 Knob
H. Anti-skating Knob
A.
B.
C.
OFF
ON
PRE-AMP
OUT PUT
D.
E.
F.
G.
H.
45
33
OFF
• Your Stir It Up Wireless uses an AC power supply and is
powered by a standard wall outlet.
• Connect the power adaptor to the wall outlet.
6
7
Quick Start Guide
BLUETOOTH® PAIRING
• Power on the external Bluetooth® device first before
turning on the BT function on the Turntable.
• Press the BT button on the turntable to turn on
Bluetooth® transmitter.
• Press button again to enable the unit to search the
Bluetooth® device till BT indicator light becomes solid.
This will indicated your devices are paired.
45
33
OFF
• Blue LED light flash
• Blue LED light stable
DISCONNECT BLUETOOTH® PAIRING
Long press and hold the BT button till the BT indicator light
turns off. Turntable will then disconnect from external device.
• Blue LED light will turn off.
8
Quick Start Guide
Quick Start Guide
PLAYING A RECORD
1. Put a vinyl record on the turntable.
2. Assemble the balance weight and set it to a proper
position.
3. To adjust the balance weight rotate the balance
weight at counter-clock wise.
4. Lift and move the tone arm to turntable. Place the
tone arm on the edge of the record.
5. Turn the RPM Dial knob to select the speed according
to the record you are playing.
6. The turntable platter will auto stop when the music
has ended. Lift the tone arm and place it to tone arm
rest manually.
To listen to side B, flip record and repeat the above steps.
*33 RPM speed to play corresponding size 33 vinyl disc
*45 RPM speed to play corresponding size 45 vinyl disc
To power the unit off Rotate the RPM Dial knob to the off
position.
Note:
Remove the needle cover before you balance the tone arm.
Hold tone arm whenever you make any adjustment or action
so as to protect the tone arm.
Do not try to adjust the balance weight while playing a
record as this could break the needle and scratch the record.
Re-secured the tone arm before transportation to protect
the needle.
Remove the balance weight before transportation to
prevent damage or breakage to the unit.
Do not stop or turn the platter manually. Moving or
jarring the turntable without securing the Tone arm
clamp could result in damage to the Tone arm.
ANTI-SKATING
45
Normally the anti-skating should be set to its minimum
setting. Anti-skate compensates for inward tracking forces
that occur with certain pick-up when the stylus nears the
33
center of the record. If the turntable is experiencing
excessive skipping while nearing the center spindle, try
OFF
increase the anti-skating in the increments indicated
on the dial. Start by adding an increment of 1, test its
performance, then increase it more, and so on.
Note: During adjusting the anti-skating knob, leave the
tone arm and balance weight alone to prevent damaging the
stylus (needle).
9
Quick Start Guide
OUT PUT
VOLUME CONTROL
1.
2.
Increase Volume: Rotate the Volume Knob clockwise.
Decrease Volume: Rotate Volume Knob counter clockwise.
HEADPHONE OPERATION VIA HEADPHONE JACK
3.
4.
Connect a set of headphone (not included) in the headphone jack.
5.
6.
Note: Never put on the headphone till you have plugged in
the headphone plug
USB TO PC RECORDING
45
Download Full instruction for the Audacity Software at:
33
http://www.audacityteam.org/download/
• Connect the Turntable and the computer via the provided
OFF
USB cable.
• Follow the instruction of the software installation steps
and operation interface.
10
11
Quick Start Guide
OFF
ON
PRE-AMP
VOLUME +
VOLUME -
Quick Start Guide
Publicidad
