Berner BP 40-82 C Manual Original página 14

OBJ_BUCH-1135-002.book Page 14 Wednesday, August 12, 2015 3:00 PM
22 Locking nut for adjustment of rebating width
23 Fastening bolt for parallel and beveling guide
24 Angle stop*
25 Locking nut for angle adjustment
26 Fastening bolt for rebating depth stop
27 Rebating depth stop*
28 Park rest*
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
Technical Data
Planer
Art. No.
Rated power input
Output power
No-load speed
Planing depth
Rebating depth
Planing width, max.
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given apply for nominal voltages [U] of
230/240 V.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted noise levels of the product
are: Sound pressure level 85 dB(A); Sound power
level 96 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and un-
h
certainty K determined according to
EN 60745-2-14: a =7.5 m/s
h
The vibration level given in this information sheet
has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with different
accessories or insertion tools or is poorly main-
tained, the vibration emission may differ. This may
significantly increase the exposure level over the
total working period.
14 | English
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not ac-
tually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
BP 40-82 C
tives 2011/65/EU, until 19 April 2016:
102519 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amend-
001342 (CH)
ments and complies with the following standards:
W 850
EN 60745-1, EN 60745-2-14.
W 450
Technical file (2006/42/EC) at:
-1
min 14000
Berner Trading Holding GmbH
mm 0 – 4.0
Bernerstraße 6
mm 0 – 24
74653 Künzelsau
mm 82
GERMANY
Armin Hess
kg 3.2
Chairman of the Managemant Board
/II
04.08.2015, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
Assembly
 Before any work on the machine itself, pull the
2 2
, K=1.5 m/s .
Changing the Tool
 Be cautious when replacing the planer blades.
Use only original Berner carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and
can be reversed. When both cutting edges are dull,
the planer blade 16 must be replaced. The carbide
blade (TC) may not be resharpened.
mains plug.
Do not grasp the planer blades by the cutting
edges. Possible danger of injury due to the
sharp cutting edges of the planer blades.
1 609 92A 1DH • 12.8.15