Tabla de contenido
Publicidad
IMPORTANT
Please read
these instructions carefully before you start to assemble this
product
.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these instructions
in
a
safe
place for
future
reference.
Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
3
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance on
your product.
Do
not attempt to
assemble the
product
in
windy or wet conditions.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children away from the assembly
area.
When using
a
stepladder or power
tools, make
sure
that you
are
following
the manufacturer's safety advice.
Do
not climb or
stand on
the
roof.
Do
not
hang or
lay on
the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy
snow load on the roof
can make
it unsafe to stand below or nearby.
Do
not
lean
against or push the product during construction.
Hot items
such
as
recently
used grills,
blowtorches
etc.
must not
be
stored inside the product.
Note:
This
product must
be
anchored on to
a
leveled surface and solid
foundation to
ensure
its
stability. Make
sure
that
screws
and anchors
are
compatible with foundation type.
Make
sure
that
there
are no
obstructions between the
assembly
area
and the final position.
Cleaning Instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before
Starting Assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and have
a
solid
base such
as
concrete,
asphalt, deck
etc.
Sort
the
parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep all small parts (screws etc.) in
a
bowl
so
they do not
get
lost.
Please
consult your
local
authorities if any permits
are
required prior to constructing the product.
The
drawings
in
this manual
are
designed for 11'x
17.2' shed + 4.1' Extension Kit.
Please
note that content list
refers
only for 11'x
17.2' shed.
11'x
17.2'
4.1'Ext.
Kit
11'x21.3'
Yukon + 2x Ext.
(11'x
17.2')
Yukon + 3x
Ext.
(11'x
21.3')
Note:
All
the extension module
steps are
marked
with
a
dashed
outline, should
be
performed
during the product's assembly
process.
Optional
Accessories
WPC
Floor Kit
WPC
Floor Kit:
If
you've purchased the
WPC
Floor
Kit
with the
product, relevant
steps are
marked
with
these icons. If you've
assembled the
product
without
the floor kit and wish to add
one, please refer
to the relevant
steps
(marked
with
these icons)
in
the assembly and perform the
necessary
adjustments.
Utility
Shed
Shelf Kit:
If
you've purchased shelf
kits,
it
is
recommended to insert
screws #411
inside the profiles'tracks during the walls'assembly.
Vertical Bicycle Hanger:
Can be
installed once the product
is
fully
assembled. Make
sure
the
bottom
wheel
is
at
floor
level.
Publicidad
Tabla de contenido
