Machine Assembly; Packaging Contents - Stiga SE 1814 Q Manual De Instrucciones

Electrosierra
Ocultar thumbs Ver también para SE 1814 Q:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 63
6
EN

4. MACHINE ASSEMBLY

PACKAGING CONTENTS

The packaging contains:
– power unit,
– bar,
– chain,
– bar cover,
– bag containing equipment and documents.
IMPORTANT
the bar and chain dismantled and the oil tank
empty.
WARNING!
ing the assembly should be done on a flat and
sta ble surface, with enough space for ma­
chi ne handling and its packaging, always
making use of suitable equipment.
Disposal of the packaging should be done in
ac cordance with the local regulations in for ce.
BAR AND CHAIN MOUNTING
WARNING!
gloves when handling the bar and chain.
Mount the bar and chain very carefully so as
not to impair the safety and efficiency of the
m achine. If in doubt, contact your dealer.
Before fitting the bar, make sure the chain brake is
not engaged; this is done by pulling the front hand
guard right back towards the body of the machine.
WARNING!
not plugged into the mains socket.
• MACHINES WITH STANDARD
CHAIN TENSION ADJUSTER
– Remove the rubber protection (1a), unscrew the
nut (1) and remove the guard to get to the drive
sprocket and the point where the bar is fitted
(Fig. 1).
– Mount the chain in the right direction on the bar.
If the tip of the bar has a nose sprocket, make
sure the drive links are correctly inserted in the
sprocket rims (Fig. 2).
The machine is supplied with
Unpacking and complet­
Always wear heavy­duty
Make sure the machine is
– Mount the bar (2) by inserting the stud bolt in
the groove and push it towards the back of the
machine body and wind the chain around the
drive sprocket (Fig. 3).
– Check that the chain tension adjuster pin (3) is
fitted properly in the hole on the bar (Fig. 4); if
it isn't, turn the chain tension adjuster screw (4)
using a screwdriver until the pin is comple tely
inserted (Fig. 5).
– Fit the guard back on without tightening the nut
(1).
– Turn the chain tension adjuster screw (4) to ad-
just the chain tension (Fig. 5).
– Raise the bar and tighten the guard nut (1)
securely using the supplied wrench, then re-
place the rubber protection (1a) (Fig. 6).
• MACHINES WITH QUICK CHAIN TENSION
ADJUSTER
– Unscrew the handle (11) and remove the
guard to get to the drive sprocket and the point
where the bar is fitted (Fig. 1a).
– Mount the chain in the right direction on the bar.
If the tip of the bar has a nose sprocket, make
sure the drive links are correctly inserted in the
sprocket rims (Fig. 2).
– Mount the bar (2) by inserting the stud bolt in
the groove and push it towards the back of the
machine body and wind the chain around the
drive sprocket (Fig. 3).
– Fit the guard back on without tightening the han-
dle (11). Check that the chain tension adjuster
pin (3) is fitted properly in the hole on the bar
(Fig. 4); if it isn't, turn the chain tension adjuster
ring-nut (12) until the pin is completely inserted
(Fig. 5a).
– Turn the ring-nut (12) to obtain the desired chain
tension level (Fig. 5a).
– Raise the bar and tighten the handle (11)
securely (Fig. 6a).
MACHINE ASSEMBLY

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Se 2014Se 2014 qSe 2016Se 2016 qSe 2216Se 2216 q

Tabla de contenido