English – Inglés – Angla
4.3.- Stop periods of less than 8 d
In case of installation stop lowe
ensure at least once a day, a d
occasional circulation of water.
4.4.- Safety instructions
All the electric machinery, m
rotary represents a potential haza
for those people not familiar wit
construction or handling. Therefore
of safety precautions must be take
safeguard the user against injuries
damages to equipment or associa
Depending on site conditions,
necessary to install ladders, acce
and passageways or foot protec
safety of servicing and maintenan
No starting of the equipment shall
unless all the fan protective screen
access doors are correctly installed
Only
qualified
personnel
service or repair this equipment.
dealing with these activities should
familiar with the equipment, associa
controls and procedures outlined in
4.4.1.- Welding and grinding o
If welding and grinding work mu
potential fire hazard of the synth
components may result. To avoid
the following instruction must be ad
a) A foam extinguisher must b
used.
b) Put a plug on the upper air
air draughts in the tower.
In case of installations with ex
the instructions in case of explos
observed.
4.4.2.- Access to the cooling tow
If maintenance to the fans, p
inside of the tower must be perform
electric switch must be disconne
following
warning must be er
prominent location:
"DO NOT CONNECT, DEATH MA
glais
8 days
wer than 8 days,
draining or an
mechanical or
zard, especially
with its design,
ore, all manners
ken, in order to
ies or to prevent
ciated systems.
s, it may be
ccess platforms
tections for the
ance personnel.
all be authorized
ens, panels and
led.
sh
shall
operate,
t. All personnel
uld be extremely
ociated systems,
in this manual.
g operations
must be done,
thetic materials
id such hazard,
adhered to:
t be ready to be
air exit to avoid
explosion risks,
losions must be
tower
, pumps or the
ormed, the main
nected and the
erected in a
AY RESULT"
Français– Fren
rench –Francés
4.3.- Arrêt de l'installatio
ation inférieur à 8 jours
En cas d'arrêt de l'in
l'installation inférieur à 8
jours, assurer au moins
ins une fois par jour une
purge ou un maintien po
ponctuel de la circulation
d'eau.
4.4. Instructions de séc
écurité
Afin de prévenir tout
ut accident et d'éviter tout
dégât
occasionné
à
à
composants, les mesures
res de sécurité adéquates
doivent être prises. En f
n fonction des conditions
du site, il sera nécessair
aire d´installer des mains
courantes ou toute autre
re équipement assurant la
sécurité du personnel de
autorisés. L´équipement
nt ne doit pas être mis en
fonctionnement sans que
que tous les éléments ne
soient correctement insta
stallés.
Le fonctionnement, l´e
l´entretien et la réparation
de ces équipements
s doivent être réalisés
seulement par du perso
rsonnel qualifié. Tout le
personnel qui réalise c
parfaitement familiarisé
é avec les équipements,
systèmes
associés,
exposés dans ce manuel.
uel.
4.4.1.- Travaux de sou
soudure et meulage
Des risques d'incend
ndie des composants en
matériaux synthétiques
es existent en cas de
réalisation des travaux
ux de soudure ou de
meulage, c'est pourquoi o
oi on doit tenir compte des
instructions suivantes:
a) Préparer un extin
tincteur à mousse.
b) Boucher la sortie
tie supérieure de l'air pour
éviter des couran
rants d'air dans la tour.
En cas d'installation d
n dans des lieux sensibles
aux explosions, on doit o
it observer les instructions
locales pour prévenir tout
out risque.
4.4.2.- Accès à la tour
our de refroidissement
Si l´on doit réaliser
ser des travaux sur le
ventilateur, la pompe ou
u à l'intérieur de la tour, il
faut débrancher l´interrup
rupteur principal et mettre
un avis bien visible.
"NE PAS BRANCHER, D
, DANGER DE MORT
l´utilisateur
ou
aux
de service et d´entretien
ces activités doit être
contrôles
co
et
procédés
Pag. 34