Publicidad
Idiomas disponibles
Idiomas disponibles
KIT COMPONENTS
• A) Radio housing trim panel • B) Brackets • C) Pocket • D) (8) #8 x 3/8" truss head Phillips screws
A
B
Metra. The World's Best Kits.
®
Mitsubishi Outlander 2014-2019
Mitsubishi Outlander
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted Charcoal high gloss
C
MetraOnline.com
2020-2021
(ES Trim)
D
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
99-7015CHG
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
–ISO DIN radio provision with pocket . .................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7005
Antenna Adapter: Not required
Visit MetraOnline.com for audio/video and steering
wheel control interface options.
TOOLS REQUIRED
• Panel removal tool
• Phillips screwdriver
Attention: With the key out of the
ignition, disconnect the negative battery
terminal before installing this product.
Ensure that all installation connections are
secure before cycling the ignition to test
this product.
REV. 7/15/21 INST99-7015CHG
Publicidad
Tabla de contenido
Manuales relacionados para Metra 99-7015CHG
Resumen de contenidos para Metra 99-7015CHG
- Página 1 Attention: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST99-7015CHG...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unsnap and remove dash panel. (Figure A) Unscrew (4) Phillips screws and remove the factory radio. (Figure B) Continue to Kit Assembly (Figure A) (Figure B) 386.257.1187 MetraOnline.com... -
Página 3: Kit Assembly
ISO DIN radio provision with pocket 1. Attach the pocket to the radio brackets with the (4) #8 x 3/8" truss head Phillips screws provided. (Figure A) 2. Mount the bracket/pocket assembly to the housing trim panel with the remaining (4) #8 x 3/8" truss head Phillips screws provided.. (Figure B) 3. Slide the radio into radio brackets and secure with screws supplied with the radio. (Figure C) (Figure A) (Figure B) (Figure C) 4. Locate the factory wiring harness and antenna, plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS. 5. Place the new radio assembly into the dash. Reconnect the negative battery terminal and test the radio for proper operation. 6. Reassemble the dash in reverse order of disassembly. REV. 7/15/21 INST99-7015CHG... - Página 4 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST99-7015CHG...
- Página 5 Asegúrese de que todas las conexiones de instalación estén seguras antes de realizar un ciclo de encendido para probar este producto. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST99-7015CHG...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Suelte a presión y quite el panel del tablero. (Figura A) Quite el radio de fábrica. (Figura B) Continúe Kit de Montaje (Figura A) (Figura B) 386.257.1187 MetraOnline.com... -
Página 7: Ensamble Del Kit
ENSAMBLE DEL KIT Provisión de radio ISO DIN con cavidad 1. Monte la cavidad en los soportes del radio con los (4) tornillos Phillips #8 de 3/8" suministrados. (Figura A) 2. Monte el ensamble del soporte/ cavidad en el panel de la moldura de la carcasa del radio con los (4) tornillos #8 incluidos. (Figura B) 3. Deslice el radio en los soportes del radio y sujételo con los tornillos suministrados con el radio. (Figura C) (Figura A) (Figura B) (Figura C) 4. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. 5. Monte el conjunto del radio en el tablero y vuelva a armar el tablero al revés de como lo desarmó. REV. 7/15/21 INST99-7015CHG... - Página 8 386-257-1186 ext. 8300, o envíe un correo electrónico a techsupport@metra- autosound.com. Antes de hacerlo, revise el folleto de instrucciones por segunda vez y asegúrese de que la instalación se realizó...