Facom 779.1000R Traducido De Las Instrucciones Originales página 18

engLish
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Charging the Battery (Fig. A, B)

WARNING: You should only charge the battery using CE
approved USB ports rated for charging high performance
devices. The 779.1000R can pull more current than
acceptable with older USB ports.
nOte: The lamp illumination function will be disabled during
battery charging. Always Charge the battery after long period of
storage (such as 6 months) to prevent permanent capacity loss.
1. Plug the type C USB charging cable
USB power adapter 9 .
2. Plug the type C USB plug of your type C USB charging
cable into the type C USB port
10
3. The battery will fully charge in 3‑4 hours. After this time
the battery is fully charged and may be used or left on
the charger. The charging indicator
when the battery is fully charged.
4. Recharge discharged batteries as soon as possible after use
or battery life may be greatly diminished. For longest battery
life, do not discharge batteries fully. It is recommended that
the batteries be recharged after each use.
nOte: To ensure maximum performance and life of lithium‑ion
battery charge the battery fully before first use.
Power Bank (Fig. A)
The power bank can be used when the lamp is in use and when
it is being charged.
1. Plug your device charging cable into the output port
2. Your device will begin to charge automatically.
nOte: If the lamp battery fully discharges, your device will
no longer charge and the lamp must be recharged.
Light Placement (Fig. A, C, D)
The area light can be used one of five ways.
• On a level surface.
• Hung from a joist or saw horse using the hang hook
Refer to Hang Hook for further instruction.
• Using the hang strap 12
object. Refer to Hang Strap for further instruction.
• Mounted to a tripod using the screw threads
on the bottom and side of the area light. Refer to Screw
Threads for further instruction.
• Using the magnets located on the bottom and sides of
8
the area light. Refer to Magnets for further instruction.
OPERATION
Hang Hook (Fig. C)

CAUTION: When the area light hangs by the hang hook,
do not shake the area light or the object from which it
hangs. Do not hang the area light from any electrical wires
or anything that is not secure. Personal injury or property
damage may occur.
16
10 into the supplied
.
2
will illuminate green
11
to attach the area light to an
located
7

CAUTION: Only use the hang hook for hanging the LED
area light. The hang hook is not intended to support
additional weight. Do not attach or hang anything
additional to the area light or risk of breakage may occur.

CAUTION: Do not use the hang hook to reach with or to
support your weight in any situation.
The built‑in hang hook
in the space you are working in.
1. To access the hang hook, pull the hook upwards, away from
the area light housing until the hook opening is exposed.
2. Secure the hang hook onto an anchored object in
your workspace.
nOte: Ensure the hang hook is fully secured and will not
slide off the anchored object before proceeding.
Hang Strap (Fig. D)
The built‑in hang strap
to objects in the space you are working in.
1. To access the hang strap, pull the strap upwards, away from
the area light housing.
2. Wrap the strap around the object you want to attach the
light to and fix the end of the strap to one of the rods as
shown in Fig. D.
nOte: Ensure the hang strap is fully secured and will not
unattach from the rods before proceeding.
Screw Threads (Fig. A)
1. Place the screw threads
mounting screw using a screw with a 1/4" bolt, and
20 threads per inch.
3
2. Rotate the area light clockwise to attach.
Magnets (Fig. A)

CAUTION: When the area light hangs by the magnets, do
not shake the area light or the object from which it hangs.
Do not hang the area light from anything that is not
secure. Personal injury or property damage may occur.

CAUTION: Only use the magnets for hanging the LED area
light. The magnets are not intended to support additional
.
5
weight. Do not attach or hang anything additional to the
area light or risk of breakage may occur.
The area light has six built‑in magnets
These magnets are intended to hold the area light in place on
metal surfaces.
On/Off Switch (Fig. A)

CAUTION: Do not stare into area light lens. Serious eye
injury could result.
To turn the area light on, slide the on/off/brightness switch
one of the three brightness levels (250 lm, 500 lm and 1000 lm).
To turn the area light off, slide the on/off/brightness switch to
the off position.
can be attached to anchored objects
5
12 can be used to attach the area light
7 of the area light on the tripod's
8 on the side and base.
1 to