BLACK&DECKER GWC1800L20 Manual De Instrucciones página 6

ENGLISH
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. Blow tube
2. Blower
3. On/Off switch
4. Battery
5. Feet
Assembly
@
Warning! Before assembly, make sure that
the appliance is switched off and the battery is
removed.
@
Warning! Always wear protective gloves when
working with your cordless sweeper.
Blow tube assembly (fig. A)
The blow tubes (1) must be assembled before use.
Align the square latches (6) on the side of the blow tubes
u
(1).
Push the blow tubes (1) firmly into each other until the
u
square latches (6) click into place.
Note! The blow tubes can be separated for storage by press-
ing in the square latches (6) on the side of the blow tube and
pulling them apart.
Mounting the blow tube (fig. B)
Align the square latches (6) on the side of the blow tube
u
(1) with the square latches (7) on the nozzle (8).
Push the blow tube (1) firmly onto the nozzle (8) until the
u
square latches (6 & 7) click into place.
Note! The blow tubes can be separated from the nozzle by
pressing in the square latches (7) on the side of the nozzle
and pulling them apart.
Fitting and removing the battery (fig. C)
To fit the battery (4), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (9) while at
u
the same time pulling the battery out of the receptacle.
6
(Original instructions)
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. D)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (4), insert it into the charger (10).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (11) will blink.
The charge is complete when the charging indicator (11)
switches to continuously on. The charger and the battery can
be left connected indefinitely. The LED will switch on as the
charger occasionally tops up the battery charge.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Switching on and off (fig. E)
Warning! Use both hands to grip the product firmly when
switching on.
To switch the appliance on, slide the on/off switch (3)
u
forward.
To switch the appliance off, slide the on/off switch (3)
u
back.
Maintenance
Your Black & Decker appliance has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper appli-
ance care and regular cleaning.
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.