(3) Celsius / Fahrenheit
• Press "°C /°F" button (B7) to select Indoor/Outdoor Temperature in Celsius mode or
Fahrenheit mode.
• If the temperature is out of the measurable range, LL.L (beyond the minimum
temperature) or HH.H (beyond the maximum temperature) will be shown on the LCD.
(4) Maximum / Minimum Temperature Recording Function:
• Press "MAX/MIN" button (B5) to see the maximum or minimum of IN/OUTDOOR
temperature.
"
" is shown on the LCD means the temperature shown is the recorded
max. temperature.
"
" is shown on the LCD means the temperature shown is the recorded
min. temperature.
• Hold "MAX/MIN" button (B5) for 3 seconds to clear the recorded maximum and
minimum reading.
7. Time and Alarm Setting
7.1 Radio Controlled Clock:
• The clock automatically starts scanning the RF 433MHz signal to register new thermo
sensor unit after new batteries inserted. After registered new channels
or press "CHANNEL" button (B8) to stop scanning, the clock will then scan the DCF
time signal automatically. Radio Control Icon "
(A3)flashes, Indicating now
(A3) turns on, Indicating signal
is receiving DCF signal
received successfully
• The clock automatically scans the time signal at 3.00 a.m. every day to maintain
accurate timing. If reception fail, scanning stops ("
again at 4.00 a.m. 5.00a.m. and 6.00a.m.
• The clock can be set to scan the time signal manually by holding "
seconds. If receptions fail, scanning stops. ("
at next hour. E.g. scanning failed at 8:20a.m. It will scan again at 9:00a.m.
•
Stop scanning by holding "[
] "button (B7) for 3 seconds.
•
The "DST" is shown on the LCD if it is in Daylight Saving Time Mode
Note: Buttons (except "LIGHT" button (B1)) will not function while scanning for DCF time
signal unless they are well received or stopped manually.
7.2 Manual Time Setting:
• Press "MODE/SET" button to select to view
Time
Date
ENGLISH 6
" (A3) flashes on LCD.
(A3) disappear, Indicating
signal reception failed
" on LCD disappear) and repeats
" button (B7) for 3
" on LCD disappear) and repeats again
• When viewing the time, hold "MODE/SET" button (B2) for 3 seconds to enter Clock/
Calendar setting mode.
• Press "▲" (B6) or "▼" (B7) button to adjust the setting and press "MODE/SET" button
(B2) button to confirm each setting.
• The setting sequence is shown as follow: Hour, Minute, Year, Month/Day sequence,
Month, Day, and Time Zone.
Note:
(1) The Time zone is used for the countries where can receive the DCF time signal but the
time zone is different from the German time.
(2) When the country time is faster than the German time for 1 hour, the zone should be set to
+1. Then the clock will automatically set 1 hour faster from the signal time received.
(3) The Time Setting Mode will automatically exit in 15 seconds without any adjustment.
7.3 12/24 Hour Display mode:
Press "(12/24)" button (B6) to select 12 or 24 hours mode.
7.4 Snooze Alarm Clock Function:
• Press " ALARM" button (B3) once see the alarm time ("AL" shown on the LCD):
• Press "Alarm" twice, to turn ON/OFF the alarm function. When alarm on,
on the LCD.
• When viewing alarm time, hold "ALARM" button (B3) for 3 seconds to enter the Alarm
Time setting. Press "▲" (B6) or " ▼ " (B7) button to adjust the alarm time, and press
"ALARM" button (B3) to confirm the setting.
• When alarming, press "SNOOZE/LIGHT" (B1) button to activate snooze alarm. "
flash on the LCD. The alarm will snooze for 5 minutes, then it alarms again. This
snooze function can be enabled for maximum 7 times.
• Except "SNOOZE/LIGHT" (B1) button, press any button to stop the snooze alarm.
8. Low batteries indication:
The low battery icon "
" will appear at particular channel indicating that thermo sensor
unit of the channel is in low battery status. The batteries should be replaced.
9. Projection & Backlight
• Press "SNOOZE/LIGHT" (B1) button, the projection and backlight shine for around 20 seconds.
• When DC adaptor plug in, push "PROJECTION ON/STANDBY" (B9) slide switch
to "ON", the projection and back light will turn on and not auto off. Push the switch
to "STANDBY", press "SNOOZE/LIGHT" (B1) button to turn on the back light and
projection for around 20 seconds.
ENGLISH 7
shown
"