Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
PARTS LIST
PART
MATERIAL CODE
NO.
1
TGS59SW-CS05-1
2
TGS59SW-CS04-3
3
TGS59SW-CS04-4
4
TGS59SW-CS04-8
5
TGS59SW-CS04-1
6
TGS59SW-CS06-1
7
TGS59SW-CS08-1
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #13)
- Hex. Key Wrench (See Part #14)
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
Step 1:
Place the table top (#1) onto a non-abrasive surface, such as
a carpet, with its underside facing upwards. Slide the legs
(#2, #3, and #4) into the plastic holders attached on the
underside of the table top (#1) rim. Fasten them together by
using screws (#8). See Figure 1.
Note:
The labels marked "L" and "R" on legs (#2 and #3) should
coincide with Figure 1 to ensure proper assembly.
!
Use the correct bolts as indicated. Do not tighten any of the bolts until the table is completely assembled.
!
Do not sit or stand on this table.
!
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
!
Keep children away during assembly. This item contains small parts that can be swallowed by children. Children should
always be under direct adult supervision while using this product.
!
Retain these assembly instructions for future reference.
!
Quote the following FQC NO. when contacting the service center.
V-4
INTENDED FOR RESIDENTIAL USE ONLY.
TGS59SW
PART
TABLE TOP
LEFT LEG
RIGHT LEG
MIDDLE LEG
SUPPORT FRAME
MESH FRAME
BACK FRAME
SERVICE CENTER TOLL FREE NO.
TEL: 1-877-539-7436
FAX: 1-877-539-7439
DO NOT RETURN TO THE STORE!
STOP
PART
Q'TY
MATERIAL CODE
NO.
1
8
17C17A0403001YX
1
9
17C40A0709001YX
1
10
17C40A0708001YX
1
11
17C40A0705001YX
2
12
17C40A0710001YX
2
13
17KAA0101----Y4
1
14
17KAC3101----Y3
FIGURE 1
2
L
8
PAGE 1 OF 3
PART
SCREW ST4.2*12
BOLT M6*25
BOLT M6*20
BOLT M6*15
BOLT M6*30
HEX. KEY WRENCH 4MM
HEX. KEY WRENCH 10MM
4
1
4
1
COURTYARD CREATIONS INC.
Q'TY
8
8
2
4
6
1
1
3
R

Publicidad

loading

Resumen de contenidos para Courtyard Creations TGS59SW

  • Página 1 Retain these assembly instructions for future reference. Quote the following FQC NO. when contacting the service center. SERVICE CENTER TOLL FREE NO. TEL: 1-877-539-7436 FAX: 1-877-539-7439 DO NOT RETURN TO THE STORE! STOP PAGE 1 OF 3 COURTYARD CREATIONS INC.
  • Página 2 FIGURE 2 FIGURE 3 #9 BOLT M6*25 #10 BOLT M6*20 Step 2: Step 3: Fasten the mesh frames (#6) to legs (#2, #3, and #4) by Insert the support frame (#5) into the plastic holders attached using bolts (#9 and #10). Keep the bolts loose. on the underside of the table top (#1) rim.
  • Página 3 Warranty • This product is covered by Courtyard Creations Inc.'s 3 year limited warranty. • Proof of purchase (dated register receipt) is required for warranty claims. • It remains the customer’s responsibility for freight and packing charges to and from the service center.
  • Página 4: Lista De Partes

    Cuando se comunique con el centro de servicio, proporcione siempre el siguiente código de control de calidad (FQC, por sus siglas en inglés). NÚMERO GRATUITO DEL CENTRO DE SERVICIO TEL: 1-877-539-7436 FAX: 1-877-539-7439 ¡NO DEVUELVA ESTE PRODUCTO A LA TIENDA! ALTO COURTYARD CREATIONS INC. PÁGINA 1 DE 3...
  • Página 5 FIGURA 2 FIGURA 3 #9 TORNILLO M6*25 #10 TORNILLO M6*20 Paso 2: Paso 3: Inserte los soportes (#5) en los sujetadores de plástico que Sujete las repisas de rejilla (#6) a las patas (#2, #3 y #4) con están fijos a la parte inferior del borde de la cubierta de la ayuda de los tornillos (#9 y #10).
  • Página 6: Lea Estas Instrucciones Completamente Antes De Empezar El Armado

    Garantía • Este producto está cubierto por una garantía limitada de tres años con Courtyard Creations Inc. • Para cualquier reclamación de la garantía es necesario presentar el comprobante de compra (recibo de caja registradora con fecha). • El cliente será responsable por los cargos de empaque y envío a y desde el centro de servicio.