Tabla de contenido
Manuales relacionados para Westinghouse Stella Mira
Resumen de contenidos para Westinghouse Stella Mira
- Página 1 ETL-ES-Stella Mira-WH17 Owner's Manual Manual del usuariO Stella Mira Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: net weight: Peso neto:...
-
Página 2: Safety Tips
ETL-ES-Stella Mira-WH17 safety tiPs OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED ' A CCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS' AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. -
Página 3: Consejos De Seguridad
ETL-ES-Stella Mira-WH17 COnsejOs de seGuridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O HERIDAS PERSONALES, MONTE EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES DE 35 LB (15,9 KGS ) O MENOS”... -
Página 4: Features Características
ETL-ES-Stella Mira-WH17 features CaraCterístiCas dOwnrOd installatiOn instalaCiÓn COn Varilla VertiCal For normal ceilings COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements Para techos normales your decor, or change the style with just a flip of the blade. -
Página 5: Preparing For Installation Antes De La Instalación
ETL-ES-Stella Mira-WH17 PreParinG fOr installatiOn antes de la instalaCiÓn Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble). -
Página 6: Mounting Bracket Installation Instalación Con Soporte De Montaje
ETL-ES-Stella Mira-WH17 MOuntinG BraCKet installatiOn instalaCiÓn COn sOPOrte de MOntaje Remove the screws from the two mating holes (2) on the canopy. Loosen (do not remove) the screws in the mating slots (1) on the canopy. Rotate the mounting bracket and remove from the canopy. - Página 7 ETL-ES-Stella Mira-WH17 MOuntinG BraCKet installatiOn MOuntinG OPtiOns instalaCiÓn COn sOPOrte OPCiOnes de MOntaje de MOntaje Choose a MOuntinG OPtiOn elija una OPCiÓn de MOntaje nOrMal dOwnrOd OPtiOn If installing downrod supplied with fan, proceed to page 8, step 6. OPCiÓn COn Varilla VertiCal nOrMal Si instala la varilla vertical incluida con el ventilador, proceda a la página 8, paso 6.
- Página 8 ETL-ES-Stella Mira-WH17 dOwnrOd PreParatiOn PreParandO la Varilla VertiCal Remove clamp pin (1) and cross pin (2) from downrod (3). Quite el pasador tipo prensa (1) desde el pasador transversal (2) de la vara (3).
- Página 9 ETL-ES-Stella Mira-WH17 PreParinG fOr installatiOn antes de la instalaCiÓn Loosen (do not remove) the screws (1) from the coupling cover (2). Remove the 4 screws (3) from the coupling cover support parts (4). Afloje (no quite) los tornillos (1) de la cubierta del acoplamiento (2). Retire los 4 tornillos (3) de las piezas de soporte de la cubierta de acoplamiento (4).
- Página 10 ETL-ES-Stella Mira-WH17 PreParinG fOr installatiOn antes de la instalaCiÓn Feed motor wires though the under cover (1) and attach the under cover (1) to the motor housing (2). Make sure to align the holes in under cover with the holes in motor housing, and tighten screws supplied (3) to secure the under cover to motor housing accordingly.
- Página 11 ETL-ES-Stella Mira-WH17 nOrMal dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal nOrMal Place down rod (1) assembly into canopy (2) and coupling cover (3), coupling cover support part (4). Feed motor wires though the down rod (1) assembly. Coloque el conjunto de la varilla (1) en el dosel (2) y la cubierta de acoplamiento (3), la parte de soporte de la cubierta del acoplamiento (4). Inserte los cables del motor...
- Página 12 ETL-ES-Stella Mira-WH17 nOrMal dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal nOrMal Insert down rod into down rod coupling. Make sure to align the hole in down rod with the hole in down rod coupling. Install cross pin (1) through coupling and down rod. Insert clamp pin (2) into cross pin until it snaps into place.
- Página 13 ETL-ES-Stella Mira-WH17 eXtended dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal MÁs larGa Slide downrod ball (1) off of downrod and remove pin (2). Loosen the downrod ball (1) from downrod (2) by removing the screw (3). Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical y Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando quitale el pasador (2).
- Página 14 ETL-ES-Stella Mira-WH17 eXtended dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal MÁs larGa Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install the screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod. If no pre-drilled hole exists in the extended downrod, tighten the screw against the downrod to secure the downrod ball.
-
Página 15: Blade Installation Instalación De Las Aletas
ETL-ES-Stella Mira-WH17 Blade installatiOn instalaCiÓn de las aletas Remove one of the screws on the switch housing plate (1), and loosen, (do not remove) the other two (2). Connect the wire plugs from the motor (3) to the wire plugs from the Insert the blades through the slots on the motor housing as shown, and use the provided light kit (4), white to white, and blue to black. - Página 16 ETL-ES-Stella Mira-WH17 liGht fiXture installatiOn instalaCiÓn del artefaCtO luMinOsO The light kit has 2 keyhole slots. Align the slots on the light kit to the protruding screws from the light kit support plate. Raise the light kit allowing the protruding screws from the support plate to enter the keyhole slots on the light kit.
-
Página 17: Wiring Options
ETL-ES-Stella Mira-WH17 wirinG OPtiOns MOuntinG OPCiÓn de CaBleadO MOntaje This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units. The frequency switches on your receiver and transmitter have been preset at the factory. Please recheck to make sure the switches on transmitter and receiver are set to the same position, any combination of settings will operate the fan as long as the transmitter and receiver are set to the same position. - Página 18 ETL-ES-Stella Mira-WH17 wirinG OPtiOns OPCiÓn de CaBleadO Once wiring step has been completed, slide the wired remote receiver in between the Make wiring connections from the house and the motor to the remote receiver as shown mounting bracket and the top of the downrod ball for downrod fans.
- Página 19 ETL-ES-Stella Mira-WH17 seCure tO CeilinG aseGure el VentiladOr al teChO For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores con varilla vertical, deslice el dosel hacia arriba hasta el soporte de montaje. The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the canopy, allow- ing the two screws to slide into the mating slots.
- Página 20 ETL-ES-Stella Mira-WH17 liGht fiXture installatiOn instalaCiÓn del artefaCtO luMinOsO Install the bulbs, B11 LED 4.5W (included). Instale las bombillas, B11 LED 4.5W (incluidas).