Publicidad
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency ener-
gy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
lf this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Should you need further certification information (FCC ID, IC) please
remove the plastic cover of the product.
FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for
general population (uncontrolled exposure). This device must be installed
to provide a separation distance of at least 20cm from all persons and
must not be collocated or operating in conjunction with any other antenna
or transmitter.
This device NRG02 complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
Caution!
This equipment may not be modified, altered, or changed in any way wi-
thout signed written permission from NETATMO. Unauthorized modifica-
tion may void the equipment authorization from the FCC and will void the
NETATMO warranty.
Canadian Compliance Statement
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This device complies with Industry Canada RF radiation exposure limits set
forth for general population (uncontrolled exposure). This device must be
installed to provide a separation distance of at least 20cm from all persons
and must not be collocated or operating in conjunction with any other
antenna or transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) il ne doit pas produire de
brouillage, et (2) l'utilisateur du dispositif doit être prêt a accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'
intention d'autres utilisateurs, il faut choisir le type d'antenne et son gain
de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
Le présent appareil est conforme aux niveaux limites d'exigences
d'exposition RF aux personnes définies par Industrie Canada. Cet
appareil doit être installé afin d'offrir une distance de séparation d'au
moins 20cm avec l'utilisateur, et ne doit pas être installé à proximité ou
être utilisé en conjonction avec une autre antenne ou un autre émetteur.
Publicidad
