Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
ATTACHING THE COVER: 10GAFBCVRxx rectangular cover assembly shown
• NOTICE: Use only electrical grade type RTV silicone sealant to insure scrub water tightness.
• Slide Gasket to underneath of AFB Flange or apply bead of Silicone compound as shown depending on ap-
plication Tile or Carpet. (See Fig. A or Fig. B).
• Pull and Lift Cover upright at 90° as shown to access Jack Screws.
• Attach cover assembly to top mounting plate using jack screws [7]. Fasten until flange is level and secure to floor.
• To adjust AFB Flange with Cover, turn jack screws [7] counter clockwise to raise or clockwise to lower. Se-
quentially turn four jack screws as needed for proper leveling of AFB Flange to floor. The jack screws have a 1
inch maximum adjustment.
Figure 7
Pull
Jack Screw (4x)
7
Gasket (use for tile application
See Fig. B)
PD2614
(Page 4)
08/14
PRINTED IN USA
Cover
AFB Flange
Pre-assembled Locknut
Jack Screw (4x)
10 GANG AFB METAL FLOOR BOX AND ACCESSORIES
Installation Instructions
Catalog no.'s AFB10G55, AFB10G55CHI
CAUTION: RISK OF ELECTRIC SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with national and local electrical codes, communication
standards, the following instructions, and any instruction included with individual devices.
NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance NEC® and
CE code requirements.
Use with 10GAFBCVRxx and 10GAFBCVRxxC series rectangular covers when used with AFB10G55 and
AFB10G55CHI series boxes.
CAUTION: PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.
See Figures 3, 4, and 5 for Box installation.
Figure 1
Catalog No
AFB10G55
Figure 2
5-3/4''
Wiring Device-Kellems
PD2614
Hubbell Incorporated (Delaware)
40 Waterview Drive
Shelton, Connecticut 06484
1-800-288-6000
5-1/2''
Catalog No
AFB10G55CHI
(Page 1)
PRINTED IN USA
08/14
English
®
Publicidad
Manuales relacionados para Hubbell AFB10G55
Resumen de contenidos para Hubbell AFB10G55
- Página 1 NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance NEC® and CE code requirements. Use with 10GAFBCVRxx and 10GAFBCVRxxC series rectangular covers when used with AFB10G55 and AFB10G55CHI series boxes. Figure 7 CAUTION: PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.
- Página 2 9. Consult electrical device mounting plate installation instructions for wiring de- Floor Box AFB Flange With Cover Depth vice installation. Use Blank Plate FB10MPBNK where no device is installed. AFB10G55, xxCHI 5-1/2” 10GAFBCVRxx or 10GAFBCVRxxC 10. Attach Flange with Cover (see figure 7). Jack...
- Página 3 • Glisser le joint sous le rebord AFB ou appliquer un cordon de silicone tel qu’illustré selon qu’il s’agisse de céramique ou de moquette. (Consulter la Fig. A ou la Fig. B). de catalogue AFB10G55, AFB10G55CHI Français • Soulever le couvercle à 90° tel qu’illustré pour accéder aux vis de nivellement.
- Página 4 Rebord AFB avec couvercle 9. Consulter les directives de la plaque de montage du dispositif électrique boîte pour réaliser son câblage. Utiliser la plaque pleine FB10MPBNK où aucun AFB10G55, xxCHI 14 cm 10GAFBCVRxx or 10GAFBCVRxxC dispositif n’est installé. Vis de 10.
- Página 5 HUBBELL DE MÉXICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un año a partir de su compra. Hubbell reparará o reemplazará el artículo a su juicio en un plazo de 60 días. Esta garantía no Núm.
- Página 6 Caja de piso Reborde AFB con tapa caja dispositivo eléctrico para efectuar el cableado. Usar una placa ciega cuando AFB10G55, xxCHI 14 cm 10GAFBCVRxx or 10GAFBCVRxxC no haya ningún dispositivo instalado. Tornillos 10. Coloque el reborde a la tapa (ver Figura 7).