GLÄSS POP-UP Manual De Instrucciones página 6

GB
INTRODUCTION
This manual is designed for use by
installers. It describes the systems
and methods to be adopted for correct
installation of the product.
The combined whirlpool baths enclosures
satisfy all directives, are not dangerous to
operators if installed, used and maintained
according to the instructions supplied by
the manufacturer, and providing electrical
and mechanical parts are maintained in
perfectly efficient order.
For this reason the instructions provided
in this manual must be meticulously
followed.
The supporting structure is highly resistant,
the bathtub enclosure is made of co-
extruded acrylic material and is assembled
directly by the manufacturer.
The bathtub enclosures are built to
conform to low voltage directives 2006/95/
EEC standard.
The protection rate for the bathtub is
IPX5, the rated voltage is 230 V; the rated
power is 900 W for the airpool/whirlpool
version.
Compliance with the level of safety laid
down by European electromagnetic
compatibility directives 2004/108/EEC is
guaranteed by implementing the following
European standards on the product:
EN 55014-1
EN 55014-2
SYMBOLS USED
IN THIS MANUAL
The symbols described below are used
in this installation manual and on certain
parts of the product itself.
CONVENTIONAL SYMBOLS AND
THEIR MEANING.
BEWARE
DANGER OF ELECTROCUTION.
This informs personnel involved that, if
the described operation is not performed
observing safety regulations, there is the
risk of electric shock.
BEWARE:
GENERAL DANGER.
This informs personnel involved that, if
the described operation is not performed
observing safety regulations, there is the
risk of physical injury.
ENGLISH
NOTE.
Provides the personnel involved with
information which, if not observed, may
lead to minor injuries to people or damage
to the product.
WARNINGS.
Provides the personnel involved with
important information.
HYDRAULIC INSTALLER.
A skilled technician able to install the
product under normal conditions and
carry out all adjustments, maintenance
and repair jobs on mechanical parts as
necessary.
The above technician is not authorised to
work on live electrical systems.
ELECTRICAL INSTALLER.
Specialist technician capable of installing
the product under normal conditions. He
is responsible for all electrical work, such
as setting, maintenance and repairs. He
is capable of working in energized control
cabinets or on electrical sockets.
BEWARE
It marks optionals present only in some
versions of the products.
OPTIONAL
Items present only if ordered.
CONSUMPTION MATERIAL
Items not provided by the manufacturer.
THE PICTURES OF THIS MANUAL
REFER TO THE LEFT VERSION. ACT
IN THE SAME WAY FOR THE RIGHT
VERSION.
SAFETY REGULATIONS
• Before installing the product, check that
the floor where the bathtub enclosure
will be installed is sufficiently level, that it
can support its weight (see installation
preparations) and that all inlets and
outlets have been provided.
• Before carrying out any cleaning or
4
maintenance work, set the appliance
to zero energy status and switch off
the double-pole switch by turning it
to "0" (OFF" position) (see installation
preparations).
• Product maintenance and setup must
be performed by specialised service
personnel only.
• Remember that all inspection and
protective panels must be refitted after
maintenance or adjustment.
• Due to its weight and size, the appliance
must be assembled by two people.
• Do not tamper with or disable or
disconnect the bathtub enclosure
devices.
• In any case, do not create by-passes or
use them for purposes other than those
for which they were installed.
• Do not remove or voluntarily tamper
with the inspection panels, and do
not remove or conceal the product
identification labels.
• Installation of electrical devices
(sockets, switches, lamps, etc.) inside
the bathroom where the appliance is to
be installed must be in compliance with
the regulations in force.
IMPORTANT.
Do not use acetic silicone.
• Read the instructions supplied with the
bottle to make sure that the silicone is
not acetic.
• If acetic silicone is used, it may
damage the acrylic parts of the bathtub
enclosure.
• If you need to replace any parts, contact
your nearest service centre and use
original spare parts only.
• At the end of the product's life, do not
abandon it in the environment; contact
a plastics disposal firm.
T h e m a n u f a c t u r e r d e c l i n e s a l l
responsibility:
• If the installation and maintenance
instructions contained herein are not
complied with.
• If the bathtub is not used or installed in
compliance with the existing standards
of the installed country.
• If the special maintenance is not carried
out by qualified personnel.