SSS Siedle EV 053-0 Manual De Instrucciones página 10

English
Application
Video installation kit for installation
in the customer's intercom compart-
ments, door constructions, letter-
boxes, etc.
Depending on the kit, there are
10 or 31 available bus addresses,
whereby the door loudspeaker occu-
pies 2 addresses.
Performance features SNG 850-...
• 10 bus addresses for supplying the
bus users
• Integrated door release and light
contact
• Programming: manual, Plug+Play
or via BPS 650-... (Windows PC)
with ZBVG 650-... and
PRI 602-... USB
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician. Failure to observe this
regulation could result in the risk of
serious damage to health or fatal
injury due to electric shocks.
• Operation at an altitude of up to
2000 m above sea level.
• Observe EN 62368-1! In a building
installation, an all-pole mains switch
with a contact opening of at least
3 mm must be provided. The device
must not be exposed to water drops
or sprayed water! Sufficient ventila-
tion must be ensured. Pay particular
attention to ensure that ventilation
slots are not covered.
• When using stranded cores as
cable material, these must be fitted
with wire end ferrules without fail.
1 In the case of video systems, the
following mounting situation must
be avoided at all costs:
• direct backlight
• direct sunlight
• very bright image backgrounds
10
• highly reflective walls opposite the
camera
• lamps or direct light sources
Scope of supply KIT EV 053-0
• BCE 053-...
• BTLE 050-...
• BRMA 050-...
• SNG 850-...
• This product information
Scope of supply KIT EV 058-0
• BCE 058-...
• BTLE 050-...
• BRMA 050-...
• BVNG 650-...
• TR 603-...
• This product information
Mounting
2 Recommended mounting height
appr. 1.60 m to centre camera.
3 Note the mounting position of the
camera, the type designation must
be legible at the top back of the
module.
4 Pick­up angle of the camera with
an angle of aperture of appr. 130°.
5 Pick­up angle of the camera with
an angle of aperture of appr. 175° in
the full screen mode.
6 Note the max. plate thickness
of 6 mm, otherwise it will lead to
adverse effects at the edge of the
camera's field of view.
7 Dimensions for securing the
camera. A cut­out with a diameter
of dia. 51 mm must be provided for
the camera.
8 With an angle of aperture of
appr. 175°, the pick­up angle of
the camera can be adjusted to any
mounting situation. Open the flap
on the back of the module with the
aid of a screwdriver.
9 Set the required picture excerpt
from the camera view (1 to 9) or full
screen (0) using the rotary switch.
Once the required picture excerpt
has been set, close the flap and
mount the module.
10 Select the picture excerpt based
on the existing mounting situation.
a Picture excerpt (1–3)
top camera alignment
b Picture excerpt (4–6)
central camera alignment
c Picture excerpt (7–9)
bottom camera alignment
Terminal assignment BCE 05x-...
TaK, TbK In-Home bus camera
branch
Ta, Tb In-Home bus
Vc, GND Camera actuation
b, c Power supply 12 V AC
Terminal assignment BTLE 050-...
Ta, Tb In-Home bus
Vc, GND Camera actuation
CD6 Call wire for DRM/COM
Tö, c Relay contact door release
Terminal assignment
BRMA 050-...
7.1 - 7.12 Door call inputs
6 common reference point
Terminal assignment SNG 850-...
L1, N Power connection
Ta, Tb In-Home bus
b, c Power supply 12 V AC
Tö, Tö Relay contact door release
Li, Li Relay contact light
Terminal assignment TR 603-...
L1, N Power connection
c, b Power supply 12 V AC
Terminal assignment
BVNG 650-...
L1, N Power connection
TaM, TbM In-Home bus monitor
branch
TaK, TbK In-Home bus camera
branch
Sa, Sb System bus audio
SaV, SbV System bus video
Tö, Tö Relay contact door
release
Li, Li Relay contact light