YATO YT-85110 Manual De Instrucciones página 16

GB
of the angles in which it is possible to block the head position.
Setting the length of the wires guard is possible after loosening the lock lever (V) and then adjustment of length of the guard and
tightening the lock lever. It is possible to steplessly adjust the length of guard in the area between movement delimiters.
Setting the angle of rotation of the cutting head is possible when you press the lock button (VI), and then you set the rotation angle
of the head under one of the angles in which it is possible to block the head position.
When using the trimmer for vertical cutting of edges (X). you can use the auxiliary wheel, which will facilitate the trimmer driving.
During normal horizontal grass cutting it is recommended the use a spacer guard. The auxiliary wheel and guard are on opposite
sides of the clamp, which located around the cutting head. To set the wheel or guard you should press the clamp lock (VII), and
then turn the clamp so the selected item is blocked in front of the trimmer.
Replacing the line
The trimmer is equipped with a spool, which automatically unwinds the line of a few millimeters each time. It is also possible to
manually unwind the line. To do this, you should pull the line segment, which is protruding from the spool, and then press the
lock button of spool (VIII). Each time, when you press, the line unwinds a few millimeters. It is not recommended to unwind the
line over a length sufficient to reach the blade guard. After starting the trimmer, the line segment, whch is extending beyond the
blade guard, is cut.
If you will not be able to further unwind the line, this means, that the line on the spool is worn and it should be replaced.
You should prepare a line section with a length and diameter shown in the table. Then install the guard cover of spool by simulta-
neously pressing both buttons lock cover (IX). Pull out the spool, then clean it and clean the interior of spool.
One end of the line should be attached to the spool, by threading it through the eyelet in the spool and tying (X). Then, the remain-
ing section of the line you should slip tightly onto the spool in the direction indicated by the arrow on the spool. During the winding,
you should avoid crossing beams and tangling of line. Leave a section of of several centimeters length and threaded it through the
hole in the spool guard (XI). Mount the spool in the spool guard, so the arrow on the spool would be pointing the same direction as
the arrow on the guard of a cutting element. Then install the guard cover of spool and check whether the line unwinds freely from
its spool, by performing the above described manual test of its unwinding.
Preparing the workplace
Before starting work, you should prepare the workplace. Before starting the work you should assign a safety zone with a radius of
at least 15 meters away from the place of work. which will not be accessible for bystanders. Make sure, that around the workplace
there are not obstacles, which can cause collision of the operator or grass trimmer during its operation.
Connecting the grass trimmer to power (XII)
Insert the battery into the power socket, with its pins facing to the inside of the shear and to the top, until the battery latches will
lock. Make sure, that the battery will not slip out during work.
You should disconnect the battery by pressing both clips, and then remove the battery from the grass trimmer housing.
Starting and stopping the grass trimmer
Make sure, that the battery is connected to the grass trimmer, and that from the cutting element guard it was removed the protec-
tion, and that the cutting element has no contact with any part of the body and other objects.
Adopt an position, that ensures balance. With one hand catch the front handle. With the other hand grasp the rear handle. Push
with your thumb the lock switch, and press the switch with other fingers, this will start the trimmer.
During operation it is not necessary to hold the lock.
The grass trimmer is stopped after releasing pressure on the switch. The cutting device can rotate for some time after the engine
is stopped. It is forbidden to stop the cutting element by applying pressing it to the ground or to other object.
After a complete stoppage of cutting element, you should disconnect the shear from the power supply by disconnecting it from the
battery. Then proceed to maintenance.
Work with the trimmer
Do not allow operation of the device at low rev speeds or during startup.
It is recommended, to move the grass trimmer from right to left during its work. You should avoid mowing, by moving the trimmer
from left to right. This will allow the operator to avoid, during cutting, the ejected remnants of cut grass.
Avoid mowing the shrubs and bushes. Work the grass trimmer near trees can damage their bark. Hitting with line stones, bricks,
walls or similar surfaces, can lead to very rapid wear of the line.
You should avoid cutting by the upper quadrant of the cutting element (IX). This will prevent situation, when the grass trimmer is
rebound in the direction of operator in the event of blockage of the cutting element during operation.
Tips useful when working
You should ensure balance and proper posture while you work. Be extremely careful when working on slippery, sloping or uneven
ground.
O R I G I N A L I N S T R U C T I O N S
16