Technical Parameters - YATO YT-82288 Manual De Instrucciones

CHARACTERISTICS OF THE PRODUCT
A hot air gun is an electric device of the second insulation class, whose purpose is to create a blow of hot air of high temperatures.
Air of such a temperature facilitates removal of old paints and varnish layers from furniture, wainscot, floors, windows, etc. Correct,
efficient and safe functioning of the tool is dependent on proper operation and this is why:
Before operating the tool the manual must be read and kept for further reference.
In the case of damage due to the safety rules and the present manual not being complied with, the supplier cannot be held
responsible.
EQUIPMENT OF THE TOOL
Hot air guns: YT-82291, YT-82292 and YT-82293 are equipped with additional nozzles and a scraper. Hot air gun YT-82288 has
no additional equipment.

TECHNICAL PARAMETERS

Parameter
Catalogue number
Nominal voltage
Nominal frequency
Nominal power
Blowing temperature (max)
Air flow
Insulation class
Net mass
Protection grade
GENERAL SAFETY CONDITIONS
NOTE! Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fire or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of accidents. Do not
work with electric tools in explosive environments, or those which contain inflammable liquids, gases or vapours. Elec-
tric tools generate sparks, which may cause a fire in case of contact with inflammable gases or vapours. Do not allow children
and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fit the mains socket. Do not modify the plug. Do not use any adapters whatso-
ever in order to adapt the plug to the socket. Unmodified plug which fits the socket reduces the risk of an electric shock. Avoid
contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body increases the risk of an
electric shock. Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool
increases the risk of an electric shock. Do not overload the power supply cable. Do not use the power supply cable in order
to carry the tool or to connect and disconnect the plug from the mains socket. Avoid contact of the power supply cable
with heat, oils, sharp tools and moving elements. Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under effects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries. Always
use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks, protec-
tive shoes, helmets and hearing protections permits to reduce the risk of serious injuries. Avoid accidental activation of the
tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a finger
on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries. Before you turn an
electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating
O P
10
Measurement unit
YT-82288, YT-82291
[V] 230~
[Hz] 50
[W] 2000
[ºC] 350 (I) / 550 (II)
[l/min] 300 (I) / 500 (II)
II
[kg] 0,76
IP20
E R A T I
GB
Value
YT-82292
230~
50
2000
50 (I) / 50 - 550 (II) / 50 - 550 (III)
300 (I) / 300 (II) / 500 (III)
II
0,80
IP20
N G M A
YT-82293
230~
50
2000
50 (I) / 70 - 600 (II) / 70 - 600 (III)
300 (I) / 300 (II) / 500 (III)
II
0,81
IP20
N U A L