Technical Data; Noise/Vibration Information; Battery Charging - Rapid BN50 Manual De Instrucciones

Technical Data

Cordless Brad Nailer
Fastener
Type
Length
Diameter
Angle
Magazine capacity, max
Dimensions
Height
Width
Length
Weight*
Battery type
Rated voltage
Capacity
Max. nailing speed
Operating capacity/full charge
(continuous operation)
Time to recharge
Permitted temperatures
Working temperature °C
Charging temperature °C
Storage temperature °C
Technical data determined with battery from delivery scope.
*Battery available in 3.0 Ah sold as separate part.

Noise/Vibration Information

Sound emission values determined according to
EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 92.9 dB(A); Sound power level
105.0 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values ah and uncertainty K determined
according to EN 60745:ah<2.725m/s
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in EN
60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
10
BN64 BN50
16 Ga brad 18 Ga brad
32-64mm 25-55mm
1.6mm 1.26mm
20 ° Straight
110 pcs 110 pcs
297mm 281mm
95mm 95mm
329mm 321mm
3.16 kg 3.10 kg
Li-Ion Li-Ion
18 V DC 18 V DC
2.0 Ah* 2.0 Ah*
60 shots/min. 60 shots/min.
approx. 500 approx. 500
shots shots
50 min 50 min
-20 ... +60 -20 ... +60
0 ... +40 0 ... +40
-20 ... +25 -20 ... +25
, K=1.5m/s .
2 2
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
Assembly

Battery Charging

• Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The "Electronic Cell Protection (ECP)" protects the lithiumion
battery against deep discharging. When the battery is
discharged, the power tool is switched off by a protective
circuit: Fasteners can no longer be shot.
IMPORTANT
After the automatic shut-off of the power tool, do not continue
to press the trigger. The battery could become damaged.
Observe the notes for disposal.
Removing the battery (see figure A)
The battery 8 has two locking levels, which are supposed to
prevent the battery from falling out in case of vibrations from
intensive use.
– Press battery unlocking button 7 (1.) and at the same time
push the battery toward the front.
– Press the battery unlocking button 7 (2.) again and pull the
battery out completely, toward the rear.
Loading the Magazine (see figures B1–B4)
Block the actuation system and remove the
battery before making any adjustments, changing
accessories, or placing the power tool aside. This
safety measure prevents accidental starting of the
power tool.
• Use only original Rapid accessories (see "Technical
Data"). The precision parts of the power tool, such as the
magazine, the outlet and the shot duct, are matched to
Rapid staples, nails and brads. Other manufacturers use
other steel qualities and sizes.
Using fasteners not permitted can damage the power tool
and cause injuries.
While loading the magazine, hold the power tool in such a
manner that the outlet 15 is not pointed at your own body or
at other persons.
– Clean the magazine slider 13 as required and make sure
that the magazine 12 is not dirty/soiled.
– Insert a fitting nail strip 16 in the T-slot at the end of the
magazine 12.