Battery Safety; Product Familiarisation; Intended Use - Silverline 811388 Manual De Instrucciones

GB

Battery Safety

WARNING: If Li-ion batteries are incorrectly used, stored or charged, they could become a fire, burn
and explosion hazard.
• Keep the battery out of the reach of children
• Only charge Li-ion batteries using the charger provided or designed specifically for your product
• Only use Li-ion batteries provided with a product or specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use, batteries should be stored at room temperature (approximately 20°C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean; foreign
objects or dirt may cause a short. Keep away from other metal objects, for example paperclips,
coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin
irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, seek medical help
Do not open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire or similar
Mini Screwdriver Safety
• Hold the power tool by insulated gripping surfaces only when performing tasks where the tool
bit comes within close proximity or may contact hidden wiring. Fasteners or cutting accessories
contacting a 'live' power source may make exposed metal parts of the power tool 'live' and could
give the operator an electric shock
• Hold the tool with a firm grip.
• Use the auxiliary handle(s), if provided. Loss of control can cause harm to the operator
• Always ensure the workpiece is secured. A properly secured workpiece using a vice or other
clamping equipment is held more secure than by hand
Always wait until the machine has come to a complete stop before setting the tool down. The tool
insert can jam, leading to a loss of control over the power tool

Product Familiarisation

1 Bit Holder
2 Magnified Bit Selection Window
3 Sliding Barrel
4 LED Charge Indicator
5 Clockwise/Trigger Lock/Anti-clockwise Switch
6 Handle
7 Charging Socket
8 LED Work Light
9 Trigger
10 Bit Cylinder
11 Mains Charger
12 Mains Charger
Connector

Intended Use

Li-ion battery powered screwdriver with loading barrel and bit cylinder for quick bit selection. For
light-duty screw-driving and fastening.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the Mains Charger Connector (12) is disconnected from the tool before use.
WARNING: Before attaching or changing any accessories or making any adjustments, ensure
the Clockwise/Trigger Lock/Anti-clockwise Switch (5) is set to the Trigger Lock position (Image D),
which prevents depressing the trigger and powering the tool.
8
Setting the trigger lock or drive direction
• The Clockwise/Trigger Lock/Anti-clockwise Switch (5) has three positions that affects the Trigger
(9) and the direction of Bit Holder (1) rotation (Image D)
• To lock the Trigger, set the Clockwise/Trigger Lock/Anti-clockwise Switch to the central position
(Image D)
• Press the Clockwise/Trigger Lock/Anti-clockwise Switch into the handle for the desired direction of
the Bit Holder rotation, clockwise or anti-clockwise (Image D)
• Visually check the bit holder rotation before connecting with the screw/fastener or workpiece
Checking the battery charge level
• Set the tool to the forward or reverse setting then pull the Trigger (9) briefly to illuminate the
charge level on LED Charge Indicator (4) (Image G)
• Alternatively, plug the Charge Connector (12) into the Charging Socket (7) and connect the
Charging Plug (11) into a power source to illuminate the LED Charge Indicator
• The LED Charge Indicator displays three colours that indicate the charge level: green, yellow,
and red
• If all three colours are illuminated, the tool has full/near full charge; if only yellow and red are
illuminated, the tool has mid-charge; and if only the red is illuminated, the tool has low-charge
and will need charging
Note: Performance of the tool may gradually decline as the battery depletes.
Charging the battery
• The tool's internal battery should be charged at 20°C (room temperature)
• Plug the Mains Charger Connector (12) into the Charging Socket (7) and connect the Mains
Charger (11) into a power source, which will illuminate the LED Charge Indicator (4) (Image G)
• When the tool's internal battery is fully-charged, the LED Charge Indicator (4) will display the
three colours: red, yellow, and green
• Disconnect the Mains Charger or USB Cable from the power source and disconnect the Mains
Charger Connector from the Charging Socket
WARNING: DO NOT leave the tool charging for an extended amount of time once it has reached
full charge. Doing so could damage the internal battery and could cause a fire hazard.
IMPORTANT: The battery will gradually lose charge in storage. Do not store the screwdriver for long
periods whilst discharged. Always charge the battery before long-term storage.
IMPORTANT: Failure to follow the correct procedure when charging the battery will result in
permanent damage. You must follow the correct procedure.
Screwdriver bits
The cordless screwdriver has the ability to holster up to 6 different hex type screwdriver bits at
any time.
Loading screwdriver bits into the Cylinder (10):
• Disconnect the tool from the Mains Charger Connector (12)
• Select the 'locked' position on the Clockwise/Trigger Lock/Anti-clockwise Switch (5) (Image D)
• Extend the Sliding Barrel (3) by holding the Handle (6) and sliding the Barrel away from the
Handle (Image E)
• Push the Bit Cylinder (10) out of the side of the Barrel and swivel to the bit loading position
(Image B)
• Slide the Bit Cylinder (10) off its spool (Image C)
• If the Bit Cylinder (10) is empty, load the bits into the slots (Image A)
• If replacing a bit, use the spool to push the existing bit out of the Bit Cylinder (10) then insert a
new bit into the empty slot (Image F) (Image A)
• Re-fit the Bit Cylinder (10) in the reverse order to removal
• Ensure the Bit Cylinder (10) is securely located (clicked) into the Barrel (3)
Selecting a screwdriver bit
• Select the 'locked' position on the Clockwise/Trigger Lock/Anti-clockwise Switch) (Image D)
• Slide the Barrel (3) into the loading position (Image E)
• Whilst looking through the Magnified Bit Selection Window (2) turn the Bit Cylinder (10) until
you see the bit you require
• The Bit Cylinder (10) will align with a click
Note: if the Bit Cylinder (10)is incorrectly aligned the Barrel (3) will not return to operating position
• Slide the Barrel back to the operating position and the selected bit will be positioned for use in
the Bit Holder (1)
Operation
IMPORTANT: Ensure the battery is fully charged before use. (See 'Checking the battery charge
level' . )
WARNING: ALWAYS set the Clockwise/Trigger Lock/Anti-clockwise Switch (5) to lock before
inserting, removing or changing bits. This will prevent accidental powering of the tool and personal
injury.
Note: The LED Work Light (8) will automatically power every time the Trigger (9) is pulled and the
tool is powered. The work light will not work when the Trigger is locked.