Intended Use - Silverline 407455 Manual De Instrucciones

GB

Intended Use

Support arm with 180° swinging positional adjustment for converting horizontal scaffold poles to a
compatible mounting frame for lifting hardware. For use with Silverline 900W Electric Hoist 500kg
and Silverline 500W Electric Hoist 250kg.
Unpacking Your Tool
WARNING: This product is heavy and as a precaution it is advised that two people assemble
the machine.
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: ALWAYS wear head protection, suitable gloves, and seek help when setting-up
this tool.
Support arm assembly
1. Place the Supporting Bar (3) and Extension Bar (6) on a secure flat surface, and remove the
Transport Fastener (18) from the end
2. Pull the Extension Bar half of its overall length from the Supporting Bar, until the Extension Bar
Securing Hole (2) is aligned with the hole located halfway along the length of the Extension Bar
3. Align the end of the Support Arm (5) with the Extension Bar Securing Hole (2), and fasten into
place using the M12 Bolt (14), Large Washer (15), Large Spring Washer (16) and M12 Nut (13)
(Image A)
Pole installation
WARNING: Do not install the hoist support arm to a pole of the incorrect diameter. The supporting
bar clamps are designed to fit the standard scaffold tube diameter of 48.3mm. Ensure the pole in
use is of the correct diameter before installation.
1. Hold the Supporting Bar Clamp (11) against the pole at the desired height for hoist installation
Note: Refer to the hoist's instruction manual for maximum height extension of the tool.
2. Insert the U-Clamp (7) through the holes in the Supporting Bar Clamp and around the pole
Secure in place by inserting the U-Clamp into the Supporting Bar Clamp, and using the Small
Flat Washer (19), Small Spring Washer (17) and M10 Nut (20) to fasten into place.
3. Using the procedure described in steps '1-3' , install the Support Arm Clamp (9) 380mm above
the Supporting Bar Clamp, measuring from U-Clamp to U-Clamp (Fig. I)
4. With assistance from another person, carefully lift the arm assembly so it is aligned with the
Supporting Bar Clamp. Mount the Supporting Bar (3) to the Supporting Bar Clamp by sliding the
Pivot Hole (4) over the Supporting Bar Mounting Shaft (12) (Image B)
5. Mount the free end of the Support Arm (5) on to the Support Arm Mounting Shaft (10), and
secure both mounting shafts with the Split Pins (21) provided (Image C)
Hoist installation
WARNING: The maximum load of the hoist support arm with the hoist mounted on the Extension
Bar (6) is 300kg. The maximum load of the hoist support arm with the hoist mounted on the
Supporting Bar (3) is 600kg. This is inclusive of the hoist's own weight (Fig. II).
Note: Ensure the hoist support arm is securely fastened to the mounting pole before installing
the hoist.
• Use the Plastic Braces (8) when installing the hoist to the Extension Bar (6) (Image D)
• Sandwich the Plastic Braces between the Extension Bar (6) and the mounting brackets on the
hoist when mounting
• If mounting the hoist to the Supporting Bar (3), it is not necessary to use the Plastic Braces
Operation
Note: The hoist support arm is capable of freely moving 180° about the axis of the mounting shafts.
• When lifting loads, use the support arm's ability to move on an axis to transfer your load securely
to the desired location
6
Accessories
• A range of accessories and consumables, including Electric Hoist 500kg, Expert Rigger Gloves
and Safety Hard Hat, is available from your Silverline stockist. Spare parts can be obtained
from toolsparesonline.com
Maintenance
General inspection
• Regularly check that all the fixing screws are tight
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth.
If available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol or
strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools