Campbell Hausfeld IB0001 Instrucciones De Operación página 3

Tabla de contenido

Publicidad

Charging
Instructions Using
120 Volt AC Adapter
(Cont'd.)
• Do not charge the unit in wet or moist
locations. Severe electric shock and injury
could result.
• Do not stand on moist or wet surfaces when
handling the charging device.
To charge the unit using the 120 Volt
AC Adapter:
1. Turn off all switches on the unit.
2. Plug the AC adapter into a standard
120 Volt AC wall outlet.
3. Plug the other end of the AC
adapter into the charger outlet on
the PowerPal (see Fig. 1).
4. Charge for at least 14-16 hours.
5. Remove the 120 Volt AC Adapter
and store it in a safe place.
Charging
Instructions Using 12
Volt DC Cord
• Prior to first use, charge unit for a
full 24 hours using the 120 Volt AC
Adapter. Do not use the 12 Volt DC
Cord for this initial charge.
• Recharging the 3-in-1 PowerPal using
the 12 Volt DC Cord will not recharge
the unit as effectively as using the
120 Volt AC Adapter. The 12 Volt DC
Cord should be used only when
absolutely necessary, otherwise
battery life may be shortened.
• If the vehicle used for recharging via
the 12 Volt DC procedure is left
running, do not charge the unit for
more than one (1) hour. After
charging for one hour, unplug the 12
Volt DC Cord and wait one hour
before checking LED Battery
Level/Charge Indicator (see Fig. 1). If
unit is not fully charged, repeat
charging process.
• Do not recharge for more than 3
hours maximum using the 12 Volt DC
method.
To charge the unit using the 12 Volt DC
Cord:
1. Turn the Master Switch to 'On' (see
Fig. 1).
2. Insert one end of the 12 Volt DC
Cord into the 12 Volt DC Power
Outlet on the vehicle or boat.
3. Insert the plug on the other end of
the DC adapter into the 12 Volt DC
Power Outlet on the front of the
unit (see Fig. 1).
4. Charge for one (1) hour. Check
battery status for full charge
(Green/Yellow/Red LED – see Fig. 1).
Do not exceed 3 hours maximum
charging time.
5. Remove the 12 Volt DC Cord and
store it in a safe place.
Jump Starting
Instructions
WARNING
!
Wear ANSI approved Z87.1
safety glasses when
working with or near lead
acid batteries.
WARNING
!
Use only on vehicles with 12 Volt DC lead-
acid battery systems. Do not connect to a 6
or 24 Volt battery system or to a dry cell
battery.
WARNING
!
Vehicles that have on-board computerized
systems may be damaged if vehicle battery
is jump-started. Before jump-starting, read
the vehicle's owner's manual to confirm
that external starting assistance is advised.
WARNING
!
Do not attempt to use this unit as a
replacement for a vehicular battery.
WARNING
!
Do not attempt to jump-start a frozen
battery.
WARNING
!
Battery clamps are ALWAYS 'ON'! Never
touch clamps to a metal conductor or to one
another. Dangerous sparks or explosion could
occur, resulting in death or serious injury.
Always store battery clamps in built-in
holsters when not in use.
1. • Turn off vehicle ignition and all
vehicle accessories (A/C, radio, lights,
cell phone, etc.)
• Make sure vehicle transmission is in
Park.
• Set emergency brake.
• Make sure area is well ventilated. If
battery to be charged is in a boat,
3
follow boat manufacturer's
instructions for purging engine
compartment and bilge.
• Do not smoke, use matches or
cigarette lighter.
2. Place the 3-in-1 PowerPal on a flat,
stable surface near the battery to be
charged. Make sure to keep clamps,
cords, clothing and body parts away
from moving vehicle components.
3. • Remove the Red Positive (+) clamp
from its holster (see Fig. 2) by
squeezing the handles and pulling
straight up.
• Connect the Red Positive (+) clamp to
the positive (+) terminal of the
battery to be jump-started.
4. • Remove the Black Negative (-) clamp
(see Fig. 2) from its holster.
• Connect the Black Negative (-) clamp
to chassis or to a solid, non-moving
metal part of the vehicle as far away
from the battery as possible. Do not
attach the black clamp to the battery
to be boosted or to fuel lines.
5. Start vehicle. Do not turn key for
longer than 3-5 seconds.
6. • After vehicle starts, remove Black
clamp first and return it to its holster.
• Next remove Red clamp and return it
to its holster.
If engine does not start, remove the
Black clamp first and place it in its
holster, then remove the Red clamp and
place it in its holster. Clean the vehicle's
battery terminals. Reconnect the clamps
as in steps 3 and 4 and try to start vehicle.
If this fails, remove the Black and then
the Red clamp. The problem may be
something other than a dead battery.
NOTICE
Recharge 3-in-1 PowerPal fully after each
use.
12 Volt DC Power
Source Instructions
1. Remove the cover on the unit's 12 Volt
DC Power Outlet (see Fig. 1).
2. Insert the 12 Volt DC plug from the
appliance (cell phone, radio, etc.) into
the 12 Volt DC Power Outlet on the
front of the unit (see Fig.1).
3. Turn the Master Switch to 'On' (see Fig. 1).
4. Turn on the appliance and operate as
usual.
www.chpower.com
Model IB0001

Publicidad

Tabla de contenido
loading

Tabla de contenido