Residual Risks; Package Contents; Electrical Safety - DeWalt DW624 Traducido De Las Instrucciones Originales

performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Specific Safety Rules for Cutters
• Hold power tool by insulated gripping surfaces, because
the cutter may contact its own cord. Cutting a "live" wire
may make exposed metal parts of the power tool "live" and
shock the operator.
Use clamps or another practical way to secure and
•
support the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable and
may lead to loss of control.
For personal protection, ALWAYS wear a dust mask.
•
• Always use cutters with a shank diameter corresponding to
the size of the collet installed in your tool.
• Always use cutters suitable for a speed of 30000 min
marked accordingly.
• Never use cutters with a diameter exceeding the maximum
diameter indicated in the Technical Data.
This router is designed to accept professional cutters of straight,
profile, rabbet, and grooved type with rated minimum speed of
30000 min .
-1

WARNING! ALWAYS CONSIDER THE FOLLOWING
COMPULSIVE CONDITIONS:
• Use 12 mm shank diameter for straight, rabbet, groove
and profile cutter
• Maximum cutter diameter:
DW624 40 mm at 35 mm cutting depth
DW625E 50 mm at 35 mm cutting depth
DW624 Groove Cutter: 50 mm at 6 mm cuttingdepth
&
DW625E

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.

Residual Risks

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D
with EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
-1 and
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Router
1 Parallel fence with fine adjustment and guide rods
1 Spanner #22
1 Dust extraction adapter
1 Guide bush
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Date Code Position (Fig. A)
The date code
39
is printed into the housing.
Example:
WALT tool is double insulated in accordance
e
, which also includes the year of manufacture,
2018 XX XX
Year of Manufacture
EngLIsh
WALT
e
; the
2
21