Elko EP inels AirSF-100 Serie Guia De Inicio Rapido página 4

Technical parameters
Power supply
Battery power:
Battery life:
Setting
Alarm Detection:
Battery status view:
DIP switch:
Acoustic signal:
Detection
Sensor:
Detection principle:
Response Time:
Measurement accuracy:
Sensitivity:
Indication
- red LED:
Communication
Protocol:
RCZ1 868 MHz
Transmitter frequency:
Approx. 50 km** Approx. 10 km** Approx. 30 km**
Range in open space:
Other parameters
Working temperature:
Storage temperature:
Operation position:
Mounting:
Protection degree:
Dimension:
Weight:
* Multiple frequency bands of B1 / B3 / B5 / B8 / B20 / B28
** Depending on network coverage
Warning
Read the operating instructions before installing the device and putting it into opera-
tion. Instruction manual is designated for mounting and also for user of the device. It is
always a part of its packing. Installation and connection can be carried out only by a per-
son with adequate professional qualifi cation upon understanding this instruction man-
ual and functions of the device, and while observing all valid regulations. Trouble-free
function of the device also depends on transportation, storing and handling. In case you
notice any sign of damage, deformation, malfunction or missing part, do not install this
device and return it to its seller. It is necessary to treat this product and its parts as elec-
tronic waste after its lifetime is terminated. Before starting installation, make sure that all
wires, connected parts or terminals are de-energized. While mounting and servicing ob-
serve safety regulations, norms, directives and professional, and export regulations for
working with electrical devices. Do not touch parts of the device that are energized – life
threat. To ensure the transmission of the radio signal, make sure that the devices in the
building where the installation is installed are correctly located. Unless otherwise stated,
the devices are not intended for installation in outdoor and damp areas, they must not
be installed in metal switchboards or in plastic cabinets with metal doors - this prevents
transmission of the radio frequency signal. iNELS Air is not recommended for control-
ling life-saving instruments or for controlling hazardous devices such as pumps, heaters
without thermostat, lifts, hoists, etc. - radio frequency transmission may be overshad-
owed by obstruction, interference, transmitter battery may be discharged etc., thereby
disabling the remote control.
AirSF-100S AirSF-100L AirSF-100NB
1x CR123A battery
approx. 2 years (depending on frequency of use)
message to the server,
vibration, optical and audible alarm
message to the server
Position 1: turn off sound signal
Position 2: turn off mechanical signal
Position 3: turn off optical signal
greater than 85 dB
contacts for fl ooding
contact between the sensor sensed liquid
2 s after connecting the scanning contacts
99.8 %
in the range 0.03 - 20 kΩ
broadcast, alarm
Sigfox LoRa
868 MHz LTE Cat NB1*
0...+50°C (Pay attention
to the operating temperature of batteries)
-30...+70°C
capture contacts for fl ooding downwards
loose
IP68
Ø 89 x 23 mm
25 g (without battery)
Replacement of a battery
1
4
Notice:
Only use batteries designed for this product correctly inserted in the device! Immediately replace
weak batteries with new ones. Do not use new and used batteries together. If necessary, clean the
battery and contacts prior to using. Avoid the shorting of batteries! Do not dismantle batteries, do
not charge them and protect them from extreme heating - danger of leakage! Upon contact with acid,
immediately rinse the aff ected area with a stream of water and seek medical attention. Keep batteries
NB-IoT
out of the reach of children. Batteries must be recycled or returned to an appropriate location (e.g.
collection container) in accordance with local legal provisions.
Placement recommendations
After inserting the battery and setting the required alarm, place the detector in any place
where flooding is supposed to occur.
The detector requires no maintenance and is intended for indoor use.
Safe handling
When handling a device unboxed it is important to avoid contact with
liquids. Never place the device on the conductive pads or objects, avoid
unnecessary contact with the components of the device.
Conductivity of liquids
Liquids suitable for detection
Type of liquid
Drinking water
Well water
River water
Rain water
Waste water
Seawater
Salt water
Natural / hard water
Chlorinated water
Condensed water
Milk
Milk serum
Fruit juices
Vegetable Juices
Broths
Wine
Beer
Coff ee
Soap toam
* Resistivity characterizes the local conductivity or resistive properties of materials which
conduct electric current.
2 / 2
ON
1 2 3
2 3
AirSF-100NB
1. Use a screwdriver to open the detector.
2. For AirSF-100NB only: Carefully insert nanoSIM (the de-
vice must not be energized when inserting or replacing
nanoSIM!)
3. Insert the battery and check the correct location (when
the battery is inserted, the detector functionality me-
ssage will be sent to the application).
4. Replace the front cover and screw it in.
Inadmissible liquids
Resistivity [Ωcm]*
• Demineralised water
5-10 kΩ
• Deionised water
2-5 kΩ
• Bourbon
2-15 kΩ • Gasoline
• Oil
15-25 kΩ
• Liquid gases
0.5-2 kΩ
• Paraffi n
~0.03 kΩ
• Ethylene glycol
• Paints
~2.2 kΩ
• High alcohol-content liquids
~5 kΩ
~5 kΩ
~18 kΩ
~1 kΩ
~1 kΩ
~1 kΩ
~1 kΩ
~1 kΩ
~2.2 kΩ
~2.2 kΩ
~2.2 kΩ
~18 kΩ