Package Contents; Warranty & Warranty Registration - Tripp-Lite B119-303-R El Manual Del Propietario

Package Contents

• B119-303-R 3x1 HDMI Switch (V 1.3)
• AC Adapter (100-240V), 9V 1.5A Output
Overview and Product Features
The B119-303-R 3x1 HDMI Switch with Remote enables you to select one of three HDMI
sources to be displayed on a single HDMI monitor. Key product features are:
• 15 watts power consumption
• UXGA display support
• HDMI Version 1.3
Installation and Operation
Figure 1: Connection of HDMI Sources
1. Connect user-supplied HDMI cables (Tripp Lite model:
P568-006) between the HDMI sources and the
B119-303-R switch inputs marked HDMI INPUT 1, 2
and 3 (Figure 1).
Figure 2: Connection of HDMI Display
2. Connect the HDMI cable between the HDMI display and
B119-303-R switch marked HDMI OUTPUT. Note:
Make sure the HDMI source is plugged into one of the
HDMI INPUT ports and the HDMI display is plugged
into the HDMI OUTPUT port (Figure 2).
Figure 3: Connection of AC Adapter
3. Connect the cord from the AC adapter to the DC 9V jack
and plug it into a wall outlet or a surge suppressor. The
front POWER LED will illuminate (Figure 3).
Figure 4: Selecting an HDMI Source
4. You can use either the included hand-held remote control
or the front SELECT button to toggle between HDMI
sources (Figure 4). Source LED illuminates when source
is selected.
• Remote Control
• Owner's Manual
• Signal rates up to 10.2 Gbps
• Pixel rates up to 340 MHz
HDMI
OUTPUT
Figure 1
OUTPUT
HDMI OUTPUT
Figure 2
HDMI OUTPUT
HDMI HDMI
INPUT INPUT
DC 9V
AC Adapter
DC 9V
or
Figure 3
Remote Control
Select Button
1
2
SWITCH
IR
1 2 3
3
3x1 HDMI Switch (V 1.3)
Model: B119-303-R
Figure 4
2
Troubleshooting
If you experience problems with your B119-303-R switch, try the following remedies:
• Connect an HDMI cable directly between the source and the display to verify that the cable is
operating. Repeat to test all cables.
• Once you confi rm that all HDMI cables are functional, use two cables to test the ports on the
B119-303-R switch. Plug one cable between the display and the HDMI OUTPUT port on the
switch. Plug the second cable between HDMI INPUT 1 and the source. Repeat with HDMI
INPUT 2 and INPUT 3, using the same source. If all ports function, the B119-303-R is
operating properly. Note: To ensure that both sources and display function properly, the
combined cable length should not exceed 16 feet.
• If the unit is plugged in and the Power LED is not lit, verify that the power supply is functioning.
Use a voltmeter to measure the output of the AC adapter to verify that 9V is present. If output is
9V, the AC adapter is functional and the B119-303-R switch has failed. Note: The positive (+) is
in the middle of the plug and the ground (-) is on the exterior of the plug.
Warranty & Warranty Registration
1-Year Limited Warranty
HDMI
OUTPUT
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one
(1) year from the date of initial purchase. TRIPP LITE's obligation under this warranty is limited to repairing
or replacing (at its sole option) any such defective products. To obtain service under this warranty, you
must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized
TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service
center with transportation charges prepaid and must be accompanied by a brief description of the problem
encountered and proof of date and place of purchase. This warranty does not apply to equipment, which
has been damaged by accident, negligence or misapplication or has been altered or modifi ed in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s)
or exclusion(s)may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifi cally, TRIPP LITE is not
liable for any costs, such as lost profi ts or revenue, loss of equipment, loss of use of equipment, loss of software, loss
of data, costs of substitutes, claims by third parties, or otherwise.
FCC Radio/TV Interference Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Tripp Lite
surge
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
suppressor
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense. The user must
use shielded cables and connectors with this product. Any changes or modifi cations to this product not expressly
POWER
approved by the party responsible for compliance could void the user's authority to operate the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Tripp Lite follows a policy of continuous improvement. Product specifi cations are subject to change without notice.
Use of this equipment in life support applications where failure of this equipment can reasonably be expected
to cause the failure of the life support equipment or to signifi cantly affect its safety or effectiveness is not
recommended. Do not use this equipment in the presence of a fl ammable anesthetic mixture with air, oxygen or
nitrous oxide.
3