Before You Begin; Tools Needed - BOERBOEL 73024442 Instrucciones De Instalación

WARNING: WARNING:
• Improper installation of this product can result in
personal injury. Always wear safety goggles when
cutting, drilling and assembling the product.
• Incorrect installation may cause harm to the gate or
individual.
• Meets Pool Safety Code*
• DO NOT allow children to play with gate.
NOTICE:
• DO NOT attempt to assemble the kit if parts are
missing or damaged.
• DO NOT return the product to the store, for assistance
or replacement parts call: 1-800-336-2383.
* Must be used with pool code approved self-closing hinges and installed at required height speci ed per local building code. Always refer to all local building codes prior to use. * Must be used with pool code approved self-closing hinges and installed at required height speci ed per local building code. Always refer to all local building codes prior to use.
QTY Description
1 Pool Latch
1 Striker
2 Brackets
2 Keys
1 Saddle
2 ⁄ " Phillips Pan Head Screws ⁄ ⁄ ⁄
1 1 1
2 2
9 Square/Phillips Combo Flat Head Screws
2 ⁄ ⁄ " Square/Phillips Combo Pan Head Screws ⁄ ⁄
5 5 5
8 8
1 ⁄ ⁄ ⁄ ⁄ " Square/Phillips Combo Pan Head
1 1 1
4 4
2
Screws
1 Striker Cover
Determine mounting height and location of the Pool Latch Determine mounting height and location of the Pool Latch
1
based upon state and local pool code requirements.
Project must meet local building codes before installation.
a.) Attach the saddle and one bracket together and
2
slide into the back of the Pool Latch. Keep bottom
of saddle ush with bottom of pool latch. Hold the
Pool Latch on the post at the determined height. With
a pencil, mark bottom of the saddle location (Fig. 1).
b.) Move upper bracket ¼" from the bottom of the
post cap and mark with a pencil the location of
the top bracket. NOTE: brackets can be ipped
when attaching to saddle for left or right handed
applications.
a.) Align the bottom of the saddle to the pencil mark.
3
NOTE: make sure the saddle and bottom bracket are
locked together.
b.) Pre-drill the hole for the bottom bracket using a
drill bit and, using a screwdriver, secure the bottom
bracket to the post using one of the 1" at head
screws provided (Fig. 2).
c.) Keeping the saddle locked with the bottom bracket,
pre-drill the three holes of the saddle using a
⁄ " drill bit and using a screwdriver, secure the bottom
⁄ ⁄ ⁄
1 1 1
8 8
bracket to the post using three of the 1" at head
screws provided. Repeat step b.) for the top bracket
using the pencil line for the height (Fig. 2).
a) Using the Phillips driver, turn saddle screw while
4
keeping vertical and push down Pool Latch. Once
threads engage, lower the latch until the bottom of the
Pool Latch is aligned with the bottom of the saddle
(Fig. 3).
a.) Place the striker on the gate, allowing the striker pin
5
to engage the latch.
b.) With a pencil, mark the location of the striker on the
gate (Fig. 4). NOTE: make sure the striker is level.
c.) While holding the striker in place, gently lift the Pool
Latch handle to release latch and open gate. Latch handle to release latch and open gate.

BEFORE YOU BEGIN:

When installing a gate on a fence, please note that vinyl gate
posts require an internal support system for weight-bearing
purposes and therefore wooden inserts or a post stiffener is
required. Post stiffener needs to be purchased separately.
Always consult your local building code department for
applicable regulations and product acceptance.
Saddle
⁄ " ⁄ ⁄ ⁄
1 1 1
8 8

TOOLS NEEDED:

Gate
Safety Glasses
Pencil
Drill
⁄ ⁄ " and ⁄ ⁄ ⁄ " Drill Bit ⁄ ⁄ ⁄
1 1 1 7 7 7
8 8 64 64
Phillips Drive
Square Drive (optional)
Tape Measure
Brackets
Striker
Fig. 1
Fig. 3
IMPORTANT!
Check codes
for minimum
height from
the ground
Fig. 2
Fig. 4