Cleaning, Maintenance And Ordering Spare Parts; Disposal And Recycling - EINHELL GE-ST 36/40 Li E Manual De Instrucciones Original

Fresadora de nieve inalámbrica
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 101
medy the problem by using batteries of higher
capacity (Ah).
It is best to clear away the snow soon after it
has fallen and in short intervals before it gets
too high.
Lift the cutter drum a little off the snow before
you switch on the machine.
Push the machine forward at a suitable wal-
king pace to leave an area that is as clear of
snow as possible.
The angle at which you push the machine has
an influence on the ejection range and on the
height of snow remaining.
Clear away the snow with the wind at your
back and in overlapping runs.
In cases of very high snow, clear away layer
by layer from the top in several runs.
For large areas draw up a plan for clearing
away the snow without it being thrown back
onto areas already cleared.
To prevent the moving parts of the machine
from freezing, allow the machine to continue
running for a few minutes after you have
finished your work. Then switch off the ma-
chine, wait for all moving parts to come to a
standstill, take out the batteries, and remove
the snow and ice that has collected on the
machine.
7. Cleaning, maintenance and
ordering spare parts
Before parking and cleaning the machine, switch
it off and remove the battery/batteries.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend cleaning the machine im-
mediately each time after use. Remove ice,
snow and dirt from the air vents in the motor
housing, from the cutter drum and from all
other parts.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
Anl_GE_ST_36_40_Li_E_SPK13.indb 21
Anl_GE_ST_36_40_Li_E_SPK13.indb 21
GB
Use a brush to remove deposits from safety
guards.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage
Remove the rechargeable battery/batteries.
Store the equipment and accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original pa-
ckaging.
10. Transport
Take out the battery/batteries.
Always hold the machine with one hand on
the additional handle and the other hand on
the carry-handle of the motor housing.
Secure the machine against slipping if you
transport it in a vehicle.
If possible, use the original packaging for
transporting the machine.
- 21 -
11.06.2021 08:39:53
11.06.2021 08:39:53

Publicidad

Tabla de contenido
loading

Tabla de contenido