Flo 79520 Manual Del Usuario página 14

GB
Safety recommendations for battery loading
Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It
is prohibited to use a damaged loading dock and charger! For the purpose of loading batteries only the charging dock and the
charger provided may be used. Using another charger may be a cause of fire or damage the tool. Batteries may be charged only
in a dry room, protected from unauthorised persons, particularly children. Do not use the charging dock and the charger without
permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required to disconnect the
charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange
smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket!
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is required
to charge it following the procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so
called "memory effect", so it is allowed to charge them at any moment. However, it is recommended to discharge them during
normal work, and then load them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it
is required to do it at least from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the
electrodes, since this would cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the
electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through ap-
proximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the relative humidity of 50%. In
order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of prolonged
storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this would
reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before loading, it is required to disconnect the charger charging dock from the mains removing the plug of the charger
from the mains socket. Furthermore, it is required to clean the battery and its contacts, removing dirt and dust with a soft and dry
cloth.
The battery has an internal load indicator. When the button is pressed the diodes will go on (VI). The more diodes are on, the
higher the load of the battery. If when the button is pressed, the diodes do not go on, the battery is discharged.
Disconnect the battery from the tool.
Insert the battery into the socket of the charger (VII).
Connect the charger to the mains socket.
A red diode will go on, indicating the loading process. At the same time, while the battery is being loaded, the diode of the battery
will successively go on.
Once the loading process has finished, the red diode will go out, and the green diode will go on, which means the charger is
powered.
It is required to remove the plug of the charger from the mains socket.
Remove the battery from the charging dock, pressing the battery lock button.
Attention! If after the charger has been connected to the mains the green diode and all the diodes of the load indicator go on, the
battery is fully charged. In such cases the charger will not start loading.
Plug the charger into a mains socket.
Unplug the charger from the mains outlet after the charging is finished.
Pull out the battery from the charging station. You should pull out the battery from the charging station immediately after the end of
charging process. Leaving the battery in the mains connected power charging station may result in its irreversible damage..
The charging station and/or the battery may become warm during charging. This is normal. When you are loading the battery in
O R I G I N A L I N S T R U C T I O N S
14