Publicidad
Idiomas disponibles
Idiomas disponibles
Wall Mantel with Base and Trim
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Important: Read entire instruction sheet before as-
sembling or installing mantel kit.
This mantel is only approved for use with CDCF, CGCF,
EFS, FDCF, HDCF, VDCF and VMH Series fireplaces. Do
not use mantel with any other product.
This mantel kit contains the following pieces:
• Hardware package
• Trim kit
• Trim kit hardware
The hardware package contains the following:
• 2 - 3" screws
• 20 - 1
⁄
" screws
1
4
Tools and items required:
• #2 Phillips screw driver (regular length)
• Slotted screw driver
• Measuring tape
• PENCIL
WS26CP and WD26CP
117197-03
GAB6094
102866-01
www.desatech.com
If any wood pieces are missing or damaged, contact the
dealer where you purchased this mantel for replacement.
If hardware is missing or damaged, contact DESA Heating
Products at 1-866-672-6040 for referral and warranty infor-
mation. You can also visit DESA Heating Products' technical
service web site at www.desatech.com.
Note: Place all mantel pieces together before actually as-
sembling mantel.
WARNING: Only use 1
header and top. Damage to the mantel will result if the
longer screws provided are used for this purpose.
/
" screws to assemble
1
4
Publicidad
Tabla de contenido
Manuales relacionados para Desa WS26CP
Resumen de contenidos para Desa WS26CP
- Página 1 If hardware is missing or damaged, contact DESA Heating This mantel is only approved for use with CDCF, CGCF, Products at 1-866-672-6040 for referral and warranty infor- EFS, FDCF, HDCF, VDCF and VMH Series fireplaces.
- Página 2 AsseMblING MANTel 6. Place mantel base next to wall at installation location. See fireplace owner's manual for installation clearances. Important: More than one person is required to lift 7. Place mantel assembly onto mantel base and center left assembled mantel. lift mantel by leg assemblies. lifting to right with back of assembly flush with back of base (see by header or mantel top could damage mantel.
- Página 3 4. Position firebox inside mantel, carefully positioning gas Mantel lines (see Figure 7). IMPORTANT: Use caution when Assembly positioning fireplace on mantel base. Base may scratch easily. 5. Place trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the trim over the shoulder screws on fireplace (see Figure 7).
- Página 4 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 Technical Service and Parts: 1-866-672-6040...
-
Página 5: Ws26Cp Y Wd26Cp
Si faltan piezas de ferretería o están dañadas, repisa de chimenea. comuníquese con DESA Heating Products al 1-866-672-6040 esta repisa está aprobada para usarse sólo con las chi- para obtener información de consulta y sobre la garantía. - Página 6 ensamble de la repisa de chimenea 5. Asegúrese de que los ensambles de los tramos queden nivelados con la parte trasera de la parte superior y de Importante: se requiere más de una persona para que la repisa esté centrada de izquierda a derecha dentro levantar la repisa montada.
-
Página 7: Instalación De La Chimenea
3. Revise que no haya fuga. Consulte Revisión de las Ensamble de conexiones de gas en el manual del propietario de la la repisa de chimenea. chimenea 4. Coloque la chimenea dentro de la repisa, colocando las tuberías de gas con cuidado (consulte la figura 7). IMPOR- TANTE: tenga cuidado al colocar la chimenea sobre la Tornillos base de la repisa. - Página 8 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004, EE.UU. Servicio técnico y piezas: 1-866-672-6040 117148-01 117148 01 Rev. C NOT A UPC 09/05...