Ec Declaration Of Conformity - Berner BACMS BL 18V Manual Original

The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the
battery pack where the temperature is below 27°C and away
from moisture Store the battery packs in a 30% - 50%
charged condition Every six months of storage, charge the
pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the process
has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and
insulated to prevent short circuit. Ensure that battery pack is
secured against movement within packaging. Do not
transport batteries that are cracked or leak. Check with
forwarding company for further advice
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate
for about 5 seconds, the fuel gauge will fl ash,and then the
tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperature of
the battery pack could raise too much. If this happens, the
fuel gauge will fl ash until the battery pack cooled down. After
the lights go off , the work may continue.
Place the battery on the charger to charge and reset it.
MAINTENANCE
Remove the battery pack before starting any work on the
appliance.
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all
times.
Use only Berner accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Berner service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at Berner.
ENGLISH
457 063 - Berner-BACMS BL 18V.indd 34 457 063 - Berner-BACMS BL 18V.indd 34
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHs), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-3-9:2015
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:2015
EN 61326-1:2013
EN 50581:2012
Künzelsau, 2017-04-28
i.V. Bert Habets
Senior Director Continuous Improvements
Authorized to compile the technical fi le.
Berner Trading Holding GmbH
Berner Straße 6
D-74653 Künzelsau
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the appliance.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear gloves!
Danger area! Keep hands, fi ngers or arms
away from this area.
Never expose tool to rain.
CAUTION! Do not stare at operating lamp.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material. Electric tools and batteries that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
34
04.10.2017 15:35:11 04.10.2017 15:35:11