Stanley FATMAX V20 SFMCSTB933 Manual Del Usuario página 13

Attaching Spool Assembly (Fig. B, C)
Use STANLEY FATMAX replacement spool STZST1169.
1. Install spindle plate
22
D shaped retaining nut on the spindle sits inside the base of
the spindle plate.
2. Rotate the spindle plate until the hole
notch in the housing. Insert the included rod through
25
the notch and into the hole, to prevent the spindle
from turning.
3. While holding the rod in place, thread the new spool
housing with spool grip cover counterclockwise.
10
Securely tighten the new spool housing onto the spindle.
Attaching Guard (Fig. D, E)

WARNING:
or personal injury could result.

WARNING:
WITHOUT GUARD FIRMLY IN PLACE. The guard must
always be properly attached on the appliance to protect
the user.
1. Assemble the guard
9
2. Using a crosshead screwdriver, insert the 2 guard screws
and tighten securely.
nOTE: An extended coverage guard is available (sold separately)
for extra coverage if desired. Use STANLEY FATMAX replacement
guard Part Number N722862.
Attaching the Auxiliary Handle (Fig. F)
1. Place the auxiliary handle
trimmer pole as shown in Figure F.
6
2. Slide the bracket of the auxiliary handle onto the
30
bottom of the handle.
3. Thread the handle bolts
the bracket from above.
4. Tighten the handle bolts. Ensure the handle is securely
attached by closing the handle clamp
5. To adjust the position of the auxiliary handle, open the
handle clamp and slide the handle up and down the pole
until it is in the desired location. Close the clamp to lock the
handle in place.
Releasing the Cutting Line (Fig. A)
In transit, the cutting line is taped to the spool housing
• Remove the tape holding the cutting line to the
spool housing.
OPERATION
Instructions for Use

WARNING:
instructions and applicable regulations.
onto the spindle , so the double
23
aligns with
24
Never remove the guard. Damage
NEVER OPERATE APPLIANCE
to the motor housing .
5
onto the top of the upper
4
through the handle and into
31
.
29
Always observe the safety

WARNING:
personal injury, turn tool off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A, H)

WARNING:
personal injury, ALWAYS use proper hand position
as shown.

WARNING:
personal injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the auxiliary handle
Switching Trimmer On and Off (Fig. A)
To turn the appliance on, squeeze the lock-off lever
the variable speed trigger
release the lock off lever. To turn the appliance off, release the
variable speed trigger.
Speed Control Switch (Fig. A)
15
This string trimmer gives you the choice to operate at a
more efficient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high- performance cutting.
To extend runtime, pull the speed control switch back toward
the battery housing
for larger projects that require more time to complete.
To accelerate the trimmer, push the speed control switch
forward toward the auxillary handle
This mode is best to cut through heavier growth and for
applications that need higher RPM.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
Trimming (Fig. I, J)
With the trimmer on, angle it and swing side to side as shown
in Figure I.
Maintain a minimum distance of 610 mm between the guard
and your feet as shown in Figure J.

WARNING:
.
10
parallel with the ground (tilted no more than 30º). This
trimmer is not an edger. DO NOT TILT the trimmer so that
the string is spinning near a right angle to the ground.
Flying debris can cause serious injury.
Bump Feed Trimmer Line Feed
Your trimmer uses 2 mm diameter diameter line that is spiral-
shaped with smooth round edges. Cutting line will wear faster
and require more feeding if the cutting is done along sidewalks
or other abrasive surfaces or heavier weeds are being cut.
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
.
4
. Once the unit is running, you may
1
into the "LO" position. This mode is best
11
into the "HI" position.
4
Keep the rotating string roughly
English
14
and then
2
3
11