DeWalt XR Flex Volt DCG200 Traducido De Las Instrucciones Originales página 39

Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 18 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A, C)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Lock-off lever
2
Spindle lock button
3
Dust extraction port
4
Main handle
5
Auxiliary handle
6
Unthreaded backing flange
7
Threaded locking flange
8
Battery
9
Intended Use
Your wall chaser has been designed for professional
chasing applications in concrete and masonry without the need
for water.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This wall chaser is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Electronic Clutch
The electronic torque limiting clutch reduces the maximum
torque reaction transmitted to the operator in case of jamming
of a diamond blade. This feature also prevents the gearing and
Battery release button
10
Depth adjustment dial
11
Guard
12
Blade access latch
13
Lower guard release
14
button
Roller wheels
15
Bluetooth® tool tag
16
mounting holes (Fig. C)
Spacers
17
electric motor from stalling. The torque limiting clutch has been
factory–set and cannot be adjusted.
Brake
Once the power is shut off, the brake stops the diamond blades
spinning more quickly than a unit without this feature. This
improves efficiency and increases user protection. Stopping
time will vary depending upon the type of wheel used.
D WALT Bluetooth® Tool Tag Ready (Fig. C)
e
Optional accessory

WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.

WARNING: Turn tool off and disconnect battery pack
before installing the D WALT Bluetooth® Tool Tag.
e

WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be sure
to securely tighten the screws.
Your tool comes with mounting holes
D WALT Bluetooth® Tool Tag (DCE041). Use only the original
e
fasteners included with the tool tag. You will need a T15 (Torx)
bit tip to install the tag. The D
e
tracking and locating professional power tools, equipment, and
machines using the D WALT Tool Connect™ app. For proper
e
installation of the D WALT Tool Tag refer to the D
e
Tag manual.
Depth Adjustment Dial (Fig. A)
To adjust the cutting depth, push in on the depth adjustment
dial and rotate to the desired depth. Ensure the depth
11
adjustment is set to the required depth of the channel.
Always return the tool to the "Park" position (P) after use.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 9 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 10
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
EngLIsh
WALT
e
WALT
e
16 for installing a
WALT Tool Tag is designed for
WALT Tool
e
WALT battery packs and chargers.
is fully charged.
9
and firmly pull the battery pack
37