TECHNICAL DATA
DUST EXTRACTOR
Stroke max. .............................................................................
Drilling capacity max. ..............................................................
Drill bit length max. .................................................................
Drilling depth max. ..................................................................
Weight .....................................................................................
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
It is also essential that you read and follow the user manual
for the hammer drill you use.
HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Do not use the dust extractor for drilling work in wood, steel
or plastic.
Do not use machines on any material containing asbestos.
The following materials should not be picked up by the
vacuum cleaner
• hazardous dust
• fl ammable, explosive dust (e.g. magnesium or aluminium
dust, etc.)
Despite using the dust extractor, a small amount of dust
may still escape.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Use a dust absorption
system and wear a suitable dust protection mask. Remove
deposited dust thoroughly, e.g. with a vacuum cleaner.
Only use the appliance if it is in perfect condition.
Never use the dust extractor without a fi lter, or if the fi lter is
damaged.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. Your power tool distributor will
normally retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System Berner chargers for charging System
Berner battery packs. Do not use battery packs from other
systems.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Lithium Ion batteries submit only discharged at the collection
points. Pole isolated to avoid short circuits.
SPECIFIED CONDITIONS OF USE
The dust extractor is designed for the extraction of dust in
drilling applications with hammer drills in stone and
concrete.
ENGLISH
BACDE 18V
.........100 mm
...........16 mm
.........160 mm
...........85 mm
..........1,6 kg
The dust extractor may only be used as an accessory for
the following machines: Berner BACDE 18V
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHs), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-6:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 50581:2012
Künzelsau, 2016-03-29
Armin Hess
Chairman of the Management Board
Authorized to compile the technical fi le
Berner Trading Holding GmbH
Berner Straße 6
D-74653 Künzelsau
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
14
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Berner accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Berner service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at Berner.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the appliance.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear a suitable dust protection mask.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked
before being dispatched from the manufacturing plant. If,
despite this fact, there are any defects, please send the item
directly to our Client Services Headquarters or to the
nearest service repair shop of the fi rm Berner.
The guarantee period is 36 months and starts from the day
of purchase, which must be proved by the original of the
purchase document. During the guarantee period the
producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement is that these are material and/or
manufacturing defects and that there has not been any
inappropriate operation [of the machine]. Furthermore, only
original accessory parts may be used, which Berner has
expressly identifi ed as suitable for the operation with Berner
machines.
15
ENGLISH