Installation Instructions - RAVAK SBKP6 Instrucciones De Montaje

GB

INSTALLATION INSTRUCTIONS

The shower cabin is delivered in parts having pre-drilled holes for connection of individual parts. The manufacturer
recommends the installation be provided by a specialized company, of which the employees are trained in mounting of
this shower cabin.
1. First, check whether the product is complete, and arrange its individual parts on the floor. Position the decorative
sides of glass walls of the box outside the shower cabin. In the plastic panel, the decorative side is the one having the
distinctly bulging surface of the decoration. The outer side of both plastic and glass panel can be recognized by the fact
that in the aluminum frame it is fitted nearer to the edge of the frame (see figure 1: A - frame, B - glass,
external side, D - internal side). Please verify, whether the pre-drilled holes of the individual parts are corresponding. If
they are not, you can return the product. Tighten the bolts gently so that the thread is not removed. The intake of warm
and cold water for the shower cabin should be plumbed-in where the corner plastic panel will be placed, at the height of
about 160-170 cm above the floor. Prepare the connection for outflow pipes of 40 mm in diameter, in the place of the
outflow siphon of the shower cabin. Always mount the shower cabin in the working (vertical) position.
2. Apply the putty along the whole length of the contact surface between the back strong side and the plastic panel.
3. Set the plastic panel to its place, level it and fasten with self-tapping screws
Later repeat the routine for the second back strong side.
4. Apply the putty along the whole length of the contact surface between the both back strong sides.
5. Attach the curved part and screw both the parts together using self-tapping screws
6. Apply the putty to the upper edge of the tray and then fit the superstructure onto the tub and drill holes
diameter.
7. Screw the superstructure to the tray using self-tapping screws
... and in the rear part. Remove the superfluous putty from the contacts of both profiles immediately after the
8.
connection is bolted !!! VERY IMPORTANT!!! Ensure that the small drain area (approx. 2mm x 1mm) at the junction
between the bottom profile and the bottom rear plastic corner moulding of both back strong sides is cleared of any
excess silicon. This drain allows water that naturally enters the profiles of the back strong sides to drain away back into
the shower tray area. If these drains are not kept clear, there is a great risk of water leaking to the outside of the shower
box.
9. At the end, seal all the connections once again with silicon putty, test the door and using the covers, cover the
mounting openings. ATTENTION! The sliding profile of the curved entry then is puttied from outside only! Put the
mounted shower tray into its final location. On the floor mark the outline of the tray and prepare water and drain
connections. When installing the tray, follow the mounting instructions for the shower tray. Attach the box using rubber
armature hoses with a minimal length of 40 cm, with outer diameter of 1/2". Attach the shower handle. Mount and try
the lower part of the siphon and fix it in its final position. Apply putty to the floor, at about 1cm (to the inside) from the
outer edge of the tub. Fix the cabin in its final position. Remove the superfluous putty from around the tub. Let the putty
harden for at least 12 hours before using the box. From the inner side of the box, fit and fix the upper part of the siphon.
A thin foil protects the polystyrene glass. Do not forget to remove the foil before putting the box into use. For covering of
back corner part, it is possible to do so by additional installation of the seperate 'back cover' white filler panel.
IMPORTANT INFORMATION!
When maintaining the shower cabin, only wipe the painted parts, glass and plastic, using a fine cloth and normal household
detergents. Never use abrasive pastes, solvents, acetones, chlor or similar substances. The manufacturer is not
responsible for damages caused by inappropriate use, installation or maintenance of the product. The manufacturer is
entitled to continuous innovation of the product. For all other information concerning the mounting, use and maintenance
ask your salesperson. The guarantee is 24 months from the date of sale. The manufacturer recommends the RAVAK
ANTICALC line of products: RAVAK ANTICALC CONDITIONER - is a preparation which perfectly renews and maintains all
the qualities of the RAVAK ANTICALC protective coating (glass filler panels only); RAVAK CLEANER - works to remove old
and dried-on debris from glass surfaces, shower frames, enamel and acrylic bathtubs, washbasins and water taps; RAVAK
DESINFECTANT - is a special preparation with considerable anti-bacterial and anti-fungal effects.
PROTECTION OF THE ENVIROMENT:
Waste materials should be re-cycled in accordance with local country laws or directives.Materials which are not suitable for
re-cycling must be disposed of at an official and suitable waste control location.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR tel.: 318 427 111, 318 427 200
fax: 318 427 269, 318 427 278, e-mail: smith@ravak.cz www.ravak.com
SBKP6 - ASBKP6
Æ
3,5 x 13.
Æ
3,5 x 13.
Æ
3,5 x 13, both in the front part...
C -
Æ
2,6 mm