Installation Instructions - RAVAK SBRV Instrucciones De Montaje

Ocultar thumbs Ver también para SBRV:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 9
GB

INSTALLATION INSTRUCTIONS

The shower cabin is delivered in parts having pre-drilled holes for connection of individual parts. The manufacturer
recommends the installation be provided by a specialized company, of which the employees are trained in mounting of
this shower cabin.
1.
First, check whether the product is complete, and arrange its individual parts on the floor. Position the decorative sides
of glass walls of the box outside the shower cabin. In the plastic panel, the decorative side is the one having the distinctly
bulging surface of the decoration. The outer side of both plastic and glass panel can be recognized by the fact that in the
aluminum frame it is fitted nearer to the edge of the frame (see figure 1: A - frame, B glass, C external side, D internal
side). Please verify, whether the pre-drilled holes of the individual parts are corresponding. If they are not, you can return
the product. Tighten the bolts gently so that the thread is not removed. The intake of warm and cold water for the shower
cabin should be plumbed-in where the corner plastic panel will be placed, at the height of about 160-170 cm above the
floor. Prepare the connection for outflow pipes of 40 mm in diameter, in the place of the outflow siphon of the shower box.
Always mount the shower cabin in the working (vertical) position.
2.
Apply the putty along the whole length of the contact surface between the back strong side and the plastic panel.
Set the plastic panel to its place, level it and fasten with self-tapping screws Æ
3.
second back strong side.
4.
Apply the putty along the whole length of the contact surface between the both back strong sides. Drill holes
diameter and fix with the help of four self-tapping screws
5.
Attach the curved part and screw both the parts together using self-driving bolts
6.
Apply the putty to the upper edge of the tray and then fit the superstructure onto the tub and drill holes
diameter.
7.
Screw the supers-tructure to the tray using self-driving bolts
8.
... and in the rear part. Remove the superfluous putty from the contacts of both profiles immediately after the connection
is bolted !!! VERY IMPORTANT!!! Ensure that the small drain area (approx. 2mm x 1mm) at the junction between the
bottom profile and the bottom rear plastic corner moulding of both back strong sides is cleared of any excess silicon. This
drain allows water that naturally enters the profiles of the back strong sides to drain away back into the shower tray area. If
these drains are not kept clear, there is a great risk of water leaking to the outside of the shower box.
9.
At the end, seal all the connections once again with silicon putty, test the door and using the covers, cover the mounting
openings. ATTENTION! The sliding profile of the curved entry then is puttied from outside only! Put the mounted shower
tray into its final location. On the floor mark the outline of the tray and prepare water and drain connections. When installing
the tray, follow the mounting instructions for the shower tray. Attach the box using rubber armature hoses with a minimal
length of 40 cm, with outer diameter of 1/2". Attach the shower handle. Mount and try the lower part of the siphon and fix it
in its final position. Apply putty to the floor, at about 1cm (to the inside) from the outer edge of the tub. Fix the box in its final
position. Remove the superfluous putty from around the tub. Let the putty harden for at least 12 hours before using the
box. From the inner side of the cabin fit and fix the upper part of the siphon. A thin foil protects the polystyrene glass. Do not
forget to remove the foil before putting the cabin into use. For covering of back corner part, it is possible to do so by
additional installation of the seperate 'back cover' white filler panel.
IMPORTANT INFORMATION!
When maintaining the shower cabin, only wipe the painted parts, glass and plastic, using a fine cloth and normal household
detergents. Never use abrasive pastes, solvents, acetones, chlor, or similar substances. The manufacturer is not
responsible for damages caused by inappropriate use, installation or maintenance of the product. The manufacturer is
entitled to continuous innovation of the product. For all other information concerning the mounting, use and maintenance
ask your salesperson. The guarantee is 12 months from the date of sale. The manufacturer recommends the RAVAK
ANTICALC line of products: RAVAK ANTICALC CONDITIONER - is a preparation which perfectly renews and maintains all
the qualities of the RAVAK ANTICALC protective coating (glass filler panels only); RAVAK CLEANER - works to remove old
and dried-on debris from glass surfaces, shower frames, enamel and acrylic bathtubs, washbasins and water taps; RAVAK
DESINFECTANT - is a special preparation with considerable anti-bacterial and anti-fungal effects.
PROTECTION OF THE ENVIRONMENT:
Waste materials should be re-cycled in accordance with local country laws or directives.Materials which are not suitable for
re-cycling must be disposed of at an official and suitable waste control location.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR tel.: 318 427 111, 318 427 200
fax: 318 427 269, 318 427 278, e-mail: smith@ravak.cz www.ravak.com
Æ
3.5 diameter x 6.5 mm.
Æ
3,5 x 13, both in the front part...
SBRV - ASBRV
3,5 x 13.
Later repeat the routine for the
Æ
3,5 x 13.
Æ
2.6 mm
Æ
2.6 mm

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Asbrv

Tabla de contenido