Before Use; After Use; During Use - Silva PAVÉ Manual

FULL VERSION MANUAL
PAVÉ
Art.no 37310-2
Thank you for choosing Silva Pavé bike light. This ultra-compact
high power bike light is designed for adventure sports users who put
performance and weight first.
The Pavé bike light is equipped with Silva Intelligent Light
is a light distribution technology that combines a wide angle flood
light with a long reach spot light. This unique light image gives the
user peripheral and long distance vision at the same time. For a
mountain biker or a road biker this translates into less head move-
ment, increased control, better balance and more speed.
Product overview
The Pavé bike light consists of the following parts:
• Light unit
• Rechargeable Li-ion battery with battery case
• Charger
• Helmet attachment
• Bike handle bar attachment
• Extension cable
• Quick guide

Before use

Battery charging
The battery needs to be charged before first use.
1. Connect the battery to the charger.
2. Connect the charger to the wall outlet.
3. On the charger there is an LED showing the battery status during
charging:
- green light = battery is fully charged (or not connected)
- red light = battery is charging
- blinking red light = battery is not working properly
Battery charging time is approximately 3 hours.
note! When the battery is fully charged the charger automatically
switches to maintenance mode.
Bike handleBar attachment
The bike handlebar attachment is designed for use on bike hand-
lebars with a dimension between 25 and 32 mm. Simply mount the
attachment by wrapping the rubber strap around the handlebar and
fasten it on the plastic hook.
2
Attach the bike light in the bike handlebar attachment by sliding the
bike light bracket into the snap-in socket.
To remove, press the push button on the bracket and move the bike
light up and out.
helmet attachment
The helmet attachment comes with a pre-mounted adhesive for easy
mounting on any helmet. It is designed to not affect the protective
characteristics of the helmet.
4
To mount the helmet attachment, make sure the surface of the
helmet is clean and dry. Remove the protective film covering the
adhesive and press the bracket onto its correct position.
If you do not want to use the adhesive on your helmet the attach-
ment is prepared for mounting with 2 cable ties on the sides. (Not
included)
Attach the bike light in the helmet attachment by simply sliding the
bike light bracket into the snap-in socket.
To remove, press the push button on the socket and move the bike
light up and out.
flexiBle Battery carrying
The battery can be carried in multiple ways; on the bike frame, the
handlebar, in a pocket, backpack or hip-bag. Use the flexible battery-
bag to attach it the way you prefer.

during use

Switch on your bike light
On the side of the bike light body there is a push button which controls
all light modes.
Each press on the button gives you the following light:
1. Turns the headlamp ON with all LEDs in maximum power.
2. Both LEDs in min mode
3. Flood light LED in min mode
4. Starts over from 1
To turn OFF the headlamp; press and hold the button for 1 second.
The flash function, which is used to attract attention, is started from
OFF mode by pressing and holding the button for 1 second. To turn
OFF; press and hold the button for 1 second.
® which
Battery indication
During operation of the bike light there will be a low battery warning
when 20% of the battery time remains. This is done by flashing both
LEDs for 1 second and repeated again after 5 seconds.
temP control
Note that the bike light body temperature will increase during use.
The bike light temperature is depending on light mode, ambient air
temperature and the airflow (speed). The Pavé bike light is equipped
with a temperature control that prevents the bike light body from
overheating by reducing the power to the LEDs.

after use

maintenance
To make sure you get maximum performance from your Pavé bike
light, clean it regularly with a wet cloth.
aBout li-ion Batteries
The battery should be stored in a dry environment within the tempe-
rature range of -20°C and +35°C.
If you would like to store your battery for a longer period (more than
30 days) the battery should not be fully charged. This may cause loss
of its characteristics.
Li-ion batteries has a discharge rate of approx. 20% over a 30 day
period. You can always charge a half full battery without damaging its
characteristics.
Do not expose the battery for extreme temperatures which may
cause fire or explosion.
Do not disassemble or mistreat the battery, risk for chemical burn.
Keep away from children.
Do not dispose of batteries in fire. This may cause an explosion.
Do not submerge the batteries in water.
Do not short circuit the contacts.
Replace only with Silva Pavé batteries.
note! Always make sure to disconnect the battery when the bike light
is not used.
technical sPecifications
Bike light weight: (including bike bracket): 50g
3
Battery weight (including battery case): 100g
Battery type: Li-ion 7.2V, 2.2 Ah
Light distance (Max/Min): 90m/55m
Lumen: 550
Burn time: Max/Min/Wide/Blink: 2h30min/10h/10h/20h
Water resistance: IPX6
Maximum output: 8W
Operative temperature range: -20 - +60º C
Protect the environment
Bike light and batteries should be recycled and must not be thrown in
the regular trash. Dispose these items in accordance with applicable
local regulations.
warranty
Silva warrants that, for a period of two (2) years, your Silva Product
will be substantially free of defects in materials and workmanship
under normal use. Silva's liability under this warranty is limited to
repairing or replacing the product. This limited warranty extends
only to the original purchaser. If the Product proves defective during
the Warranty Period please contact the original place of purchase.
Make sure to have your proof of purchase on hand when returning
the product. Returns cannot be processed without the original proof
of purchase. This warranty does not apply if the Product has been
altered, not been installed, operated, repaired, or maintained in
accordance with instructions supplied by Silva, or has been subjected
to abnormal physical or electrical stress, misuse, negligence or acci-
dent. Neither does the warranty cover normal wear and tear. Silva is
not responsible for any consequences, direct or indirect, or damage
resultant from use of this product. In no event will Silva's liability
5
exceed the amount paid by you for the product. Some jurisdictions
do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This Warranty is valid and may be processed only in the country of
purchase.
6
For more information please visit www.silva.se
2
3
7
8
4
5
6
7
8
=
=
=
!
Visit: www.silva/enviroment
for more information about the
Waste Electrical and Electronic
Equipment (WEEE) Directive.