Technical Parameters; Other Information - Elko EP PS1M Manual De Instrucciones

Technical parameters

Input
Voltage range:
Tolerance:
Effi ciency:
Burden without load (max.):
Burden with full load (max.):
Inrush current:*
Output
Rated voltage:
Vol. setting range:
Rated current:
Rated power:
Ripple & Noise:
Output indication:
Tolerance of output voltage:
Overload protection:
Overvoltage protection:
Overcurrent protection:
Short circuit protection:

Other information

Operating temperature:
Operating humidity:
Storage temperature:
Dielectric strength:
Isolation resistance:
Overvoltage category:
Pollution degree:
Max. cable size:
Terminal torque:
input terminals
output terminals
Protection degree:
MTBF:
Mounting:
Dimensions:
Weight:
Standards:
* the stated values are valid for the full load from the source
Warning
Device is constructed for connection for 1-phase main alternating -current voltage and must be installed according to norms valid in existing state. Connection according to the
details in this direction. Installation, connection, setting and servicing should be installed by qualifi ed electrician staff only, who learn this instruction and functions of device. For
right device protection should be fronted-end certain element. Before starting installation must be main switch in position "SWITCH OFF" and device should be out of voltage. Don´t
install device to suppliers surcharge electro-magnetic interference. By right installation of device is provide good air circulate to don´t pass maximal operating temperature, in case of
higher ambient temperature and permanent working. For installation and setting use screw-driver cca 2 mm. The device is full-electronic - installation should be eff ected according
to this. Function without problems is too dependent on previous type of transportation, storing and manipulation. In case of any vestige of destruction, deformation, non-function
or missing part, don´t install and made claim to seller. Product may be, after passing operating time, disassemled, recycled or puted on protected tip.
PS1M-15/12V PS1M-15/24V PS2M-24/12V PS2M-30/24V
85% 86%
0.3W / 4VA 0.5W / 4VA 0.3W / 8VA
16W / 30VA 17.5W / 32VA
max. 25A at 115V AC/60Hz
max. 45A at 240V AC/50Hz
12V DC 24V DC
11 - 13V 23 - 25V
1.25A 0.625A
15W 15W
120mV 150mV
blue LED
max. 1x 2.5 mm
0.5 Nm
90 x 18 x 58 mm
78 g
PS3M-54/12V PS3M-60/24V
AC 100 - 240 V (50-60 Hz)
± 10%
88% 89%
0.4W / 8VA 0.3W / 7VA
30W / 50VA 33W / 60VA 60W / 95VA
max. 30A at 115V AC/60Hz
max. 60A at 240V AC/50Hz
12V DC 24V DC
11 - 13V 23 - 25V 11.4 - 12.6V
2A 1.25A
24W 30W
120mV 150mV 120mV
blue LED
5 %
from 130 % - 200% rated output power
from 110 % - 145% rated output power
from 110 % - 180% rated output power
temporarily disconnecting the output
-20°C to +50°C
20% ~ 90% RH non-condensing
-40°C .. +80°C
3kV AC
100M Ω / 500V DC / 25°C (77°F) / 70% RH
III.
2
2 , max. 2x 1.5 mm 2 solid wire / with sleeve max. 1x 2,5 mm
0.3 Nm
0.5 Nm
IP20
200 000 hours minimum, full load at 25°C ambient temperature
DIN rail EN 60715
90 x 35 x 58 mm
120 g
IEC60950-1, UL508, TUV EN61558-2-16
2 / 2
PS4M-85/12V PS4M-92/24V
88% 90% 88%
0.5W / 6.5VA 0.4W / 11VA
70W / 111VA 95W / 150VA
max. 35A at 115V AC/60Hz
max. 70A at 240V AC/50Hz
12V DC 24V DC 12V DC
22.8 - 25.2V 11 - 13V
4.5A 2.5A 7.1A
54W 60W 85.2W
150mV 120mV
green LED
2
0.3 Nm
90 x 52.5 x 58 mm
190 g
90%
0.1W / 12VA
105W / 160VA
24V DC
23 - 25V
3.83A
92W
150mV
blue LED
0.3 Nm
90 x 70 x 58 mm
270 g