NVT Phybridge FLEX24 Guía De Instalación Rápida

QUI CK IN STALL GUIDE - F LEX24
The FLEX managed switch delivers fast Ethernet and PoE++ (50 watts per port)
over multiple pairs of UTP cable with six times the reach of traditional switches.
FLEX was designed to make the migration to IP quick, easy and cost effective
by leveraging an existing 1, 2 or 4-pair UTP infrastructure.
NOTE: Please see page 2 for important safety instructions
F L E X24
Removable Power Supply
RUN
ALARM
FAULT
Status LEDs
I nst all at i on Deta i ls
System Grounding: See Page 5
Location and Regional Specifications:
The FLEX24 can be installed in any indoor location in all countries except
Finland, Norway and Sweden, where, in these 3 Nordic countries, it must be
installed in a restricted access location.
FLEX24 kan installeras på valfri plats inomhus i samtliga länder utom Finland,
Norge och Sverige; i dessa nordiska länder måste den installeras på en plats
med begränsad åtkomst.
Space Requirements:
1. Select a standard 19" equipment rack or, for a standalone installation, a flat, stable surface capable of supporting the size and weight of the FLEX24, its installable
components and cabling.
2. Ensure that you have enough rack space for all equipment. Shelves and rear supporting brackets are not mandatory.
Location Requirements:
Power - The FLEX24 switch must be placed within 6 feet of an available power source. Do not use an extension cord to connect the equipment to a power outlet.
Ventilation - To ensure proper ventilation of the FLEX24, leave at least 2 inches of unobstructed space on all sides of the unit. If the fans are blocked, the unit could
overheat.
Downlink – The adapters should be installed a minimum of 6 feet away from the FLEX24 switch.
Installation procedures will be trouble free if you ensure that the following items are available before you begin:
• The FLEX24 switch, all cables and accessories you received in the FLEX package.
• SFP transceiver modules for the Gbic uplink trunks (user-supplied) if connecting over fiber.
• Fiber optic LAN cables for the Gbic uplink trunks (user-supplied) if connecting over fiber.
• Standard CAT5e copper LAN cables for the GbE uplink trunks (user supplied).
• UTP cable for the downlink ports (user-supplied).
• Serial console cable for the CONSOLE port, provided as an accessory in the product package.
• Standard CAT5e copper LAN cable for the MGMT port (optional). Only needed if out-of-band management is required (user supplied).
• Protective ground cable (user supplied).
H A R D WARE T O POL OGY AND INSTAL L ATIO N O VE RVIEW
1. Remove the FLEX24 switch and all accompanying accessories.
2. Install the rackmount brackets for rack mounting. Unit fits in standard 19" racks
3. Install the protective grounding conductor (please refer to the System Grounding
section of this guide).
4. Remove all legacy cameras or phones from the cabling.
Note: It is extremely important that non-IP cameras are not connected when you
power on the FLEX24.
5. Connect the infrastructure cable to the RJ45 on the FLEX24 switch.
6. Connect the uplink cable from a Gigabit port to the NVR or network switch.
Note: This connection also permits in-band management over Ethernet when
bridged mode is disabled (non-default setting).
7. For power share, daisy chain FLEX24 switches using DC cables (see below).
8. Power up the FLEX24.
9. For troubleshooting, please refer to the Hardware Installation Guide located at
www.nvtphybridge.com.
10. To revert back to factory defaults, hold the reset button for at least 10 seconds.
Note: In band management will be enabled after a factory reset. This can be
disabled using the pal-set-bridged outband command.
888.901.3633 | +44 (0) 208 977 6614 | www.nvtphybridge.com
F L E X 24
Management (MGMT) &
Console Port
2 Mini-Gbic Fiber Optic
Ports
GbE 1 1 3
Mgmt
Gbic 1
2 4
Reset Gbic 2 GbE 2 Console
Reset
2 10/100 Base-T
Ethernet Ports
24 RJ45 Connectors With Link/Activity LEDs
5 7 9 11 13 15 17 19
6 8 10 12 14 16 18 20
FLEX24 kan installeres overalt indendørs undtagen i Finland, Norge og
Sverige, hvor i disse tre nordiske lande den skal installeres på et sted med
begrænset adgang.
FLEX24 kan installeres innendørs i alle land unntatt Finland, Norge og Sverge.
I disse tre nordiske landene må den installeres på et sted med begrenset
tilgang.
FLEX24 Managed Switch
To NVR
RUN
or Server
ALARM
FAULT
Reset
FLEX Pack age Inc ludes :
21 23
22 24
If endpoint is within 328ft (100m) FLEX
adapter is not required.
PoE over 2- or 4-pair
UTP up to 2,000ft (610m)
GbE 1 1 3 5 7 9 11 13 15 17 19 21 23
Mgmt
Gbic 1
2 4 6 8 10 12 14 16 18 20 22 24
Gbic 2 GbE 2 Console
The Most Robust PoE Capabilities
on the Market
Four switches can be stacked together for power
sharing, load balancing and power redundancy. The
FLEX24 switch comes standard with PowerWISE
technology.
Copyright 2019 NVT Phybridge | 445-0001-C | Page 1
1 x FLEX24 Unit
1 x Rackmount Bracket Kit
1 x Console Cable
1 x Power Cable
1 x Quick Install Guide
Endpoint
FLEX-C
Endpoint
FLEX-Link
Endpoint
FLEX-Link
Long Reach PoE over UTP
55VDC Local Power Optional
FLEX4
Endpoint
Endpoint
FLEX4
Long Reach PoE over UTP
Endpoint
Endpoint
55VDC Local Power Optional