NVT Phybridge CLEER24 Guía De Instalación Rápida

QUI CK IN S TA L L G U ID E - C L E E R 24
The CLEER (Coax Leveraged Ethernet Extended Reach) family of data switches
delivers Ethernet and Power over Ethernet over Coax cable with multiple times
the reach of traditional data switches. With the CLEER24 switch customers can
transform their existing Coax infrastructure for IP device deployment.
NOTE: Please see page 3 for important safety instructions
C LE ER24
Removable Power Supply
RUN
ALARM
FAULT
Status LEDs
In st a l l at i o n D e t a i l s
System Grounding: See Page 5
Location and Regional Specifications:
The CLEER24 can be installed in any indoor location in all countries except in
Finland, Norway and Sweden, where, in these 3 Nordic countries, it must be
installed in a restricted access location.
CLEER24 kan installeras på valfri plats inomhus i samtliga länder utom Finland,
Norge och Sverige; i dessa nordiska länder måste den installeras på en plats
med begränsad åtkomst.
Space Requirements:
1. Select a standard 19" equipment rack or, for a standalone installation, a flat, stable surface capable of supporting the size and weight of the CLEER24, its
installable components and cabling.
2. Ensure that you have enough rack space for all equipment. Shelves and rear supporting brackets are not mandatory.
Location Requirements:
Power - The CLEER24 switch must be placed within 6 feet of an available power source. Do not use an extension cord to connect the equipment to a power
outlet.
Ventilation - To ensure proper ventilation of the CLEER24, leave at least 2 inches of unobstructed space on all sides of the unit. If the fans are blocked, the unit
could overheat.
Downlink – The EC-Link adapters should be installed a minimum of 6 feet away from the CLEER24 switch.
Installation procedures will be trouble free if you ensure that the following items are available before you begin:
• The CLEER24 switch, all cables and accessories you received in the CLEER package.
• All EC-Link required for connecting the IP endpoint devices, provided with the product package according to the quantity ordered.
• SFP transceiver modules for the Gbic uplink trunks if connecting over fiber.
• Fiber optic LAN cables for the Gbic uplink trunks (user-supplied) if connecting over fiber.
• Standard CAT5e copper LAN cables for the GbE uplink trunks (user supplied).
• Coax cable for the downlink ports (user-supplied).
• Serial console cable for the CONSOLE port, provided with the product package.
• Standard CAT5e copper LAN cable for the MGMT port (optional). Only needed if out-of-band management is required (user supplied).
H AR D WARE T OPOLOGY AND INS TAL L AT IO N OV E R V IE W
1. Remove the CLEER24 switch and all accompanying accessories.
2. Install the rackmount brackets for rack mounting. Unit fits in standard 19" racks.
3. Install the protective grounding conductor (please refer to the System Grounding
section of this guide).
4. Remove all legacy cameras or phones from the Coax cable.
Note: It is extremely important that non-IP, non-PoE cameras are not connected
when you power on the CLEER24.
5. Connect EC-Link to the Network jack on the IP endpoint and connect the BNC
Jack on the EC-Link to the Coax cable.
6. Connect the Coax cable to BNC connectors on the CLEER24 switch.
7. Connect the uplink cable from a Gigabit port to the NVR or network switch.
Note: This connection also permits in-band management over Ethernet when
bridged mode is disabled (non-default setting).
8. For power share, daisy chain CLEER24 switches using DC cables (see below).
9. Power up the CLEER24.
10. To revert back to factory defaults, hold the reset button for at least 10 seconds.
Note: In band management will be enabled after a factory reset. This can be
disabled using the pal-set-bridged outband command.
888.901.3633 | +44 (0) 208 977 6614 | www.nvtphybridge.com
C L E E R 24
Management (MGMT) &
Console Port
2 Mini-Gbic Fiber
Optic Ports
1 3
GbE 1
Mgmt
Gbic 1
2 4
Reset Gbic 2 GbE 2 Console 1 2 3 4 5
2 10/100/1000 Base-T
Reset
Ethernet Ports
24 BNC Female Connectors
5 7 9 11 13 15 17
6 8 10 12 14 16 18
6 7 8 9 10 11 12 13 14 15 16 17 18 19
24 Downlink
Status LEDs E C - L I N K
Network Infrastructure
BNC Port
CLEER24 kan installeres overalt indendørs undtagen i Finland, Norge og
Sverige, hvor i disse tre nordiske lande den skal installeres på et sted med
begrænset adgang.
CLEER24 kan installeres innendørs i alle land unntatt Finland, Norge og Sverge.
I disse tre nordiske landene må den installeres på et sted med begrenset
tilgang.
CLEER24 Managed Switch
To NVR
GbE 1
Mgmt
RUN Gbic 1
or Server
ALARM
FAULT Reset Gbic 2 GbE 2 Console
CAT5
NVR
The Most Robust PoE Capabilities
on the Market
Four switches can be stacked together for power
sharing, load balancing and power redundancy. The
CLEER24 switch comes standard with PowerWISE
technology.
C L E E R P a c k a g e I nc lud es :
19 21 23
1 x Rackmount Bracket Kit
20 22 24
20 21 22 23 24
E C - L i n k P a c k a g e I nc l ud es :
Ethernet Side
RJ45 Port
1 3 5 7 9 11 13 15 17 19 21 23
2 4 6 8 10 12 14 16 18 20 22 24
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Coax Up to 600M
100MB With PoE
Copyright 2020 NVT Phybridge | 413-0001-G | Page 1
1 x CLEER24 Unit
1 x Console Cable
1 x Power Cable
1 x Quick Install Guide
1 x EC-Link
Endpoint
Endpoint
Endpoint
Endpoint
Endpoint