Personal Safety; Before Use; Aligning Your Blades; Oiling Your Clipper Blades - Mellerware SWIFT Manual De Instrucciones

2.2. Personal safety:

2.2.1. CAUTION: Do not leave the appliance unattended
during use as there is a risk of an accident.
2.2.2. This appliance is only for domestic use, not for
industrial or professional use. It is not intended to be
used by guests in hospitality environments such as
bed and breakfast, hotels, motels, and other types of
residential environments, even in farm houses, offices
and other work environments.
2.2.3. This appliance is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance by
a person responsible for their safety.
2.2.4. This appliance is not a toy. Children should be
supervised to ensure that they do not play with the
appliance.
2.3. Use and care:
2.3.1. Fully unroll the appliance's power cable before
each use.
2.3.2. Do not use the appliance if the parts or acces-
sories are not properly fitted.
2.3.3. Unplug the appliance from the mains power
supply when not in use and before undertaking any
cleaning task.
2.3.4. This appliance should be stored out of reach
of children.
2.3.5. Do not store the appliance if it is still on/hot.
2.3.6. Never leave the appliance unattended when in
use and keep out of the reach of children.
2.3.7. If, for some reason, the appliance were to catch
fire, disconnect the appliance from the mains power
supply and DO NOT USE WATER TO PUT THE FIRE
OUT.
2.4. Service:
2.4.1. Make sure that the appliance is serviced only
by suitably qualified technician, and that only original
spare parts or accessories are used to replace existing
parts/accessories.
2.4.2. If the power cord is damaged, the manufacturer
or its service agent or a similarly qualified person must
replace it in order to avoid a hazard.
2.4.3. Any misuse or failure to follow the instructions
for use renders the guarantee and the manufacturer's
liability null and void.
3. Instructions for use

3.1. Before use:

3.1.1. Remove the appliance's protective film(if ap-
plicable).
3.1.2. Before using the product for the first time, clean
the parts that will come into contact with your head in
the manner described in the cleaning section.

3.2. Aligning your blades:

3.2.1. Your clippers were carefully examined to ensure
that the blades were oiled and aligned before leaving
the factory.
3.2.2. Blades must be realigned if they have been
removed for cleaning or replacement.
3.2.3. To realign the blades, each upper blade tip
should be in line with the corresponding lower blade
tip.
(The bottom blade's teeth tips should be approximately
1.2mm below the top blade's teeth tips.)
3.2.4. If blade alignment is incorrect, add a few drops
of oil to the blades, switch on the clipper for a few
seconds, switch off and unplug. Loosen the screws
slightly and adjust. Tighten the screws again after the
blade is aligned.
3.2.5. To change the blades, use a Phillips screw driver
to loosen the 2 screws.
3.2.6. Remove blade and replace it with a new blade.
3.2.7. Align the top blade then place the bottom blade
over the top blade and insert the screws and tighten
slightly.
3.2.8. Align the bottom blade as explained above and
tighten the screws further to secure the bottom blade
in place.

3.3. Oiling your clipper blades

3.3.1. To keep your clipper in peak condition, the
blades should be oiled before every use.
3.3.2. Do not use hair oil, grease, and oil mixed with
kerosene or any other solvent. The solvent will evapo-
rate and leave a thick layer of oil which may slow down
the blade's motion.
1.2mm