Redmond RI-C222-E Manual Del Usuario página 5

Ocultar thumbs Ver también para RI-C222-E:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31
Steam ironing
The most efficient steam ironing can be achieved in • • or • • • temperature modes.
Turn the steam output control dial into the required position. If the dial is in
steam feature is disabled (use the mode for dry ironing). Turn the steam output control dial
in direction towards
position to increase the steam output.
Plug in the iron. Heating indicator on the housing will light up to indicate the heating. Once
the soleplate reaches the required temperature the heating indicator will go out, indicating
that the iron is ready to use.
NOTE! Constant steam is only generated when the iron is in horizontal position and set to high
temperature. If the steam feature is enabled (the steam output control dial is not in
and the temperature setting is too low, water may drip from the soleplate.
Steam Shot
The Steam Shot feature is used to eliminate stubborn wrinkles. The feature can be used
during steam ironing when the heating indicator on the housing is out. If the heating indi-
cator is lit, wait for the soleplate to reach the selected temperature before using the Steam
Shot feature. The Steam output control dial must not be in
Briefly press the Steam Shot button during ironing for extra steam. Allow an interval of 2-3
seconds between the shots. Steam Shot feature can be used for vertical steaming.
NOTE! When the iron is set to low temperature (• position) water may drip from the soleplate,
the Steam Shot feature may not be applicable.
Vertical steam
The REDMOND RI-C222-E Steam Iron can be used in an upright position to remove wrinkles from
hanging drapes, curtains, tulle, as well as dress clothes without taking them off the hangers.
1. Turn the steam output control dial into
2. Turn the temperature control dial into "Max" position.
3. Wait until the soleplate reaches the required temperature (the heating indicator goes out).
4. Hold the iron vertically with the soleplate facing the garment. To avoid burning deli-
cate fabrics hold the iron a few centimeters away from the garment.
5. Move the iron from top to bottom briefly pressing the Steam Shot button. Return to
horizontal position every fifth time you press the button.
6. If heating indicator lights up, stop steaming and wait for the soleplate to reach the
required temperature. Resume the steaming after the heating indicator goes out.
CAUTION! The iron generates high temperature steam! Do not touch steam to prevent burning.
Never iron clothes on the body!
Dry ironing
You can use the iron for dry ironing even if the water tank is full. However, if using the
feature for a long period of time do not fill the tank with too much water.
1. Turn steam output control dial into
position.
2. Turn the temperature control dial to select the temperature appropriate for your fabric.
3. After soleplate reaches selected temperature and heating indicator goes out, the iron
is ready to use.
position the
position)
position.
position.
Water spray feature
Use the water spray feature to dampen hard-to-iron fabrics, remove stubborn wrinkles, and to
iron difficult areas such as collars, etc. Press the water spray button
slowly and smoothly for a dense spray
quickly for vaporized spray
The feature can be used as often as required from any temperature mode, as long as there
is enough water in the water tank.
Auto shut-off feature
The auto shut-off feature ensures safety and reduces energy consumption. The iron auto-
matically shuts off when left unattended:
after 30 seconds of inactivity in horizontal position or on its side (tipped over)
after 8 minutes of inactivity in vertical position
After the auto shut-off occurs the soleplate stops heating, audible signal is heard, the auto shut-off
indicator on the handle starts flashing. To continue ironing take the iron by the handle. The auto
shut-off indicator will stop flashing, the heating indicator will light up. Once the soleplate reaches
the required temperature the heating indicator will go out, indicating that the iron is ready to use.
Anti-drip feature
The anti-drip feature prevents water from dripping onto fabric and enables to iron even the
most delicate garments. Use low temperature setting (• position) to iron delicate fabrics.
After each use
Turn the temperature control dial into "Min" position and the steam output control dial into
position. Unplug the iron from electrical outlet. Open the water tank cap and gently shake
the iron above the sink to empty the tank. Place the iron into a vertical position.
Wait for the soleplate to cool down thoroughly. Wind the cord around the heel of the iron.
Store in vertical position.
Fabric Ironing Chart
Symbol of the
Temperature
temperature
control dial
Fabric
mode
position
Acrylic
Polyamide (cap-
ron, nylon)
Polyurethane
SYNTHETICS
Acetate
Polyester
RI-C222-E
GBR
to dampen the fabric:
Ironing recommendations
Iron carefully. Do not use steam iron-
ing to prevent water from dripping
out of soleplate and staining the
fabric
Iron on reverse side, fabric cannot
withstand high heat. Acetate dries fast
and needs little ironing
Iron using a damp press cloth
5

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido