Publicidad
Idiomas disponibles
Idiomas disponibles
Led
The
ECOMAT
motion
detector
electromagnetic waves and captures their echoes. Any changes in the echoes are
detected by the sensor indicating the presence or persons or animals and a
microprocessor controls the connected lights or application. The ECOMAT detects
within a radius of action of between 0.5 and 12 metres, with a 270º coverage.
INSTALLATION
The assembly and installation of electric apparatus must be carried out by
authorised personnel.
The unit is internally protected against interference by a security circuit. However,
certain especially strong magnetic fields can alter its operation.
WARNING: Disconnect the power supply prior to installing the unit.
MOUNTING
It is wall-mounted using the included flat bracket, wall-plugs and screws. A special
bracket is included for corner installation. The ideal sensor wall-installation height
is between 0.3 and 2.4 metres. It must be installed in a dry location free from any
possible splashes. It must not be installed in front of metal objects because this
could affect its capture distance. The electromagnetic waves emitted by ECOMAT
cannot penetrate metal objects.
Once the bracket is secured to the wall in the desired location, the ECOMAT
should be slid into position along the slide until it is fully secured.
Securing
bracket
Remove the cover with a slight rotation forwards and loosens the securing screw
for the connections cover for access to the terminal block.
Pass the connection wires through the cavity in the lower part of the unit, or
through the wiring access marked on the base.
Push the connector with
a screwdriver to open
and insert wire
ECOMAT
MOTION DETECTOR
"Range" Potentiometer
"Lux" Potentiometer
Cover
emits
superhigh
frequency
(5.8
12 m.
- Stiff wire between
2
0,75 and 2 mm
.
- The lenght of insulation to
remove should be 7 mm.
It must be connected in accordance with the following drawing:
ENG
Incorrect wiring connections could destroy the unit.
Once connected, close the cover again and tighten the screw.
Example of an installation on a false ceiling (non-metallic):
GHz)
PUTTING INTO SERVICE
There are three potentiometers behind the front cover:
TIME: Allows timing adjustment from three seconds to thirty minutes.
Timing commences after detecting the last movement.
R
RANGE: The detecting range is adjustable between 0.5 and 6 metres.
LUX: Adjustable between 0.5 Lux (night) and 2,000 Lux (day).
Ten seconds after the unit is switched on the sensor enters AUTO mode. Turn the
TIME to minimum (-) and the LUX potentiometer to maximum. Move in front of the
sensor until the connected device lights come on. This provides an idea of the
detection field range.
Set the TIME and LUX potentiometers to the desired positions.
The LED will flash three times when the unit passes to AUTO mode.
For the changes made to take effect in the potentiometers in the adjustment
of the equipment, it is necessary to get out from the detection area and wait
for the installation to be turned off.
TECHNICAL SPECIFICATIONS
Power supply
Sensor
Switching power
Maximum recommended loads
Incandescent lamps
Fluorescent tubes
Low voltage halogen (12 Vac)
Halogen (230 Vac)
Low consumption lamps (CFL)
Low consumption lamps (Downlights)
Led lamps
Power consumption
Capture angle
Detection range
Luminosity range
Timing range
Operating temperature
Protection index
Protection class
DIMENSIONS
06/05.2015
N L N L
1
AC IN 230 V~
230 V~ 50 Hz
5.8 GHz
µ 6 A 230 Vac cos φ = 1
1300 W
1300 VA
1300 VA
1300 W
1300 VA
1300 VA
500 VA
9 VA (1,4 W)
270º
From 0.5 to 12 metres front and up to
6 metres to the side, installed at a
height of 2.1 metres
From 0.5 to 2,000 Lux
From 3 seconds to 30 minutes
From 0ºC to +50ºC
IP 20 in accordance with EN60529
Class II in accordance with
EN 60335
78
ORBIS TECNOLOGÍA ELÉCTRICA, S.A.
Lérida, 61
E–28020 MADRID
Telephone:+ 34 91 5672277;
Fax:+34 91 5714006
E-mail: info@ orbis.es
http://www.orbis.es
42
A016.13.53383
Publicidad
