PLAYBACK
PLAY SETUP
1. While on the Home Screen, press MENU.
2. Use the UP / DOWN buttons to select "Play Setup" and press MENU.
3. Use the UP / DOWN buttons to scroll through the following Play Setup parameters. When you have
selected one, use the FWD / BACK buttons to change its setting.
a. Track Select: Selects the channel(s) that will be heard during playback.
"Stereo," "Left," "Right," and "Vocal Cut." (Note: Vocal Cut may not work on some files.)
b. Special: Adds certain effects to the audio heard during playback. Choose between "Off," "Bass
Compensate" (which boosts low frequencies), and "3D Effect" (which creates the effect of
surround sound).
c. Play Mode: Controls how tracks are played. Choose between "Once" (each track is heard once
before moving to the next one), "Loop" (the selected track repeats), and "Loop All" (the entire list
of tracks repeats).
d. Volume: Controls the playback volume, adjustable between 0 (softest) and 32 (loudest).
4. When you are finished, press BACK / CANCEL until you return to the Home Screen.
HOW TO PLAYBACK AUDIO
1. Configure your PLAY SETUP properly (as described above).
2. Connect your headphones or monitors to the HEADPHONES output. You can adjust the volume with
the VOLUME buttons.
3. On the Home Screen, select a track to play by pressing FWD / BACK. The file name will appear
above the level meters.
4. Press PLAY to start playback.
•
You can use the PLAY / PAUSE button to pause and resume playback.
•
You can press the FWD / BACK buttons to skip to the next or previous track. Holding either
button will scan through the current track.
•
You can loop a section of a file during playback using the LOOP A–B button. See LOOPING for
more information.
•
You can navigate other menus (with the MENU button and other controls) during playback.
•
When the track has ended, the next song will be determined by the Play Mode (as described in
PLAY SETUP).
5.
Press STOP to stop playback.
EFFECTS
EFFECTS SETUP
1. While on the Home Screen, press MENU.
2. Use the UP / DOWN buttons to select "Effect" and press MENU.
18. MONITOR – Turns the HEADPHONE output on / off. Hold it down for 2
seconds to turn PalmTrack's speaker on / off.
19. EFFECT – Press this button to activate and select an effect.
20. LOOP A-B – Press this button to set the beginning of a loop (Point A). Press
it a second time to set the end of the loop (Point B) and restart the loop.
RECORDING
RECORD SETUP
Before recording we recommend selecting the appropriate RECORD SETUP
options.
1. While on the Home Screen, press MENU.
2. Press MENU to select "Record Setup."
3. Use the UP / DOWN buttons to scroll through the following Record Setup
parameters. When you have selected one, use the FWD / BACK buttons to
change its setting.
a. Sample Rate: The sampling rate of your recording.
b. Rec Format: The file type and bitrate of your recording.
c. Input Select: The number of input channels that will be recorded. Select
"2 Mic" if you want to record only through the built-in mic, LINE IN, or
EXT MIC jack. Select "4 Mic" if you want to record through the built-in
mic and the LINE IN or EXT MIC jack simultaneously.
d. Auto Gain: Select "On" to allow the recording input sensitivity to be
adjusted automatically or "Off" to disable it.
e. Vocal Enhance: Enhances a recording's vocals by boosting its
frequency band while lowering the others. Choose between "Off," "Level
One," and "Level Two." ("Level Two" is the greatest amount of vocal
enhancement.)
4. When you are finished, press BACK / CANCEL until you return to the Home
Screen.
HOW TO RECORD
1. Configure your RECORD SETUP properly (as described above).
2. If you are recording with an external mic, connect it to the EXT MIC input. If
you are recording an external audio source from its line-level output, connect
it to the LINE IN jack.
3. Press REC. The button will flash red indicating PalmTrack is in Record
Standby Mode.
4. Check your levels by monitoring the volume meters on the LCD as your
sound source is playing. The meters should neither be too low nor too high.
Adjust the volume of your sound source (if possible) and/or adjust the
recording input level with PalmTrack's REC VOL –/+ buttons.
5. Monitor the sound of your recording from the HEADPHONES output. You
can adjust the headphone volume with the VOLUME buttons.
6. Press PLAY to start recording. The REC button will light solid red and the
time shown on the LCD will elapse as PalmTrack records. (You may use the
PLAY / PAUSE button to pause and resume recording.)
7. Press STOP to stop recording and save the file.
Choose between
gra
mo
18. MO
Ma
19. EF
20. LO
Pú
GRAB
CONF
Recom
GRABA
1.
Es
2.
Pu
3.
Us
de
AD
a.
b.
c.
d.
e.
4.
Cu
CÓMO
1.
Co
arr
2.
Si
gra
con
3.
Pu
mo
4.
Ve
fue
alt
en
5.
Mo
aju
6.
Pu
roj
Pa
y r
7.
Pu
REPRODUCCIÓN
CONFIGURACIÓN DE REPRODUC
1.
Estando en la pantalla Home (In
2.
Use los botones ARRIBA / AB
MENU.
3.
Use los botones ARRIBA / A
reproducción. Cuando haya se
a.
Track Select (Selección
reproducción. Elija entre
vocal). (Nota: Vocal Cut pu
b.
Special (Especial): Se usa
"Off" (Desactivado), "Bass
(Efecto 3D) (que crea el efe
c.
Play Mode (Modo de repro
(cada pista se oye una vez
(Loopear todas) (se repite l
d.
Volume (Volumen): Se usa
(el más fuerte).
4.
Cuando termine, pulse VOLVER
CÓMO REPRODUCIR EL AUDIO
1.
Configure correctamente la repr
2.
Conecte los auriculares o monit
VOLUME.
3.
En la pantalla Home (Inicio), se
del archivo arriba de los medido
4.
Pulse REPRODUCIR para inicia
•
Puede usar el botón REPR
•
Puede pulsar los botones
cualquiera de los botones, s
•
Puede loopear una sección
información, vea LOOPEAD
•
Puede navegar otros menú
•
Cuando termina la pista, e
CONFIGURACIÓN DE REP
5.
Presione STOP para detener la
EFECTOS
CONFIGURACIÓN DE EFECTOS
1.
Estando en la pantalla Home (In
2.
Use los botones ARRIBA / ABA
3.
Use los botones ADELANTE /