Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8" Phillips screws
A
Metra. The World's Best Kits.
®
Fiat 500 2016-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DDIN radio provision
• Painted scratch resistant matte black
B
C
MetraOnline.com
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
95-6544B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com for
additional adapters and accessories.
Antenna Adapter: 40-EU55
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• T-25 Torx driver • Cutting tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 5/14/18 INST95-6544B
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-6544B
Resumen de contenidos para Metra 95-6544B
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST95-6544B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unsnap and remove the climate control 3. Remove (4) T-25 Torx from the radio trim cover panel. (Figure A) panel including vents and remove the panel. (Figures D, E)) 2. Remove (2) T-25 Torx screws and unclip 4. Remove (4) T-25 Torx to remove the and remove the painted dash panel. (Figures B,C) radio (Figure F) Continue to Kit Preparation (Figure A) (Figure D) (Figure B) (Figure E) (Figure C) (Figure F) 1.800.221.0932 MetraOnline.com... -
Página 3: Kit Preparation
1. Cut and remove the shaded area from 1. Attach the radio brackets to the radio the sub-dash to allow clearance for the trim panel using (4) #8 x 3/8” Phillips aftermarket radio. (Figure A) screws supplied. (Figure A) 2. Slide the radio into the completed Remove Continue to Kit Assembly assembly, and then secure it to the shaded area assembly using screws supplied with the radio (Figure B). 3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the (Figure A) (Figure A) proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 4. Reassemble the dash in reverse order of disassembly. (Figure B) REV. 5/14/2018 INST95-6544B... - Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST95-6544B...
- Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST95-6544B...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche y retire el panel de cubierta 3. Quite (4) tornillos T-25 Torx del panel de del control de clima. (Figura A) moldura de radio, incluidas las ventilas, y retire el panel. (Figura D,E) 2. Retire (2) tornillos T-25 Torx y 4. Quite (4) tornillos T-25 Torx para retirar desenganche y retire el panel del tablero pintado. (Figura B,C) el radio. (Figura F) Continuar la preparación del kit (Figura A) (Figura D) (Figura B) (Figura E) (Figura C) (Figura F) 1.800.221.0932 MetraOnline.com... -
Página 7: Preparación Del Kit
Phillips #8 de 3/8” incluidos. (Figura A) 2. Deslice el radio en el ensamble Quite el área Continúe con el ensamble del kit terminado y luego, sujételo al ensamble sombreada con los tornillos incluidos con el radio. (Figura B) 3. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y realice todas las conexiones necesarias al radio. Metra (Figura A) (Figura A) recomienda el uso de adaptadores de acoplamiento adecuados de Metra o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para asegurarse de que funciona correctamente. 4. Vuelva a armar el tablero en el orden inverso de cómo lo desarmó. (Figura B) REV. 5/14/2018 INST95-6544B... - Página 8 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/14/18 INST95-6544B...